Your task as a sharpener is to remove that fatigued metal and expose the steel underneath, the fresh strong steel and bring side A and B of the knife together at the Apex precisely, sounds easy doesn’t it? Like peeling a layer off and having a fresh start, over and over. Of course there is much more to it than this but in very basic terms, you want the abrasive properties of the water stone to abrade the fatigued metal away, like an eraser.

The Fallkniven DC3 Diamond/Ceramic Whetstone Sharpener will make a believer out of anyone willing to invest a bit of time in the process. A big advantage of this stone is that it can be taken anywhere, used anywhere, without any form of lubrication and will produce an amazing sharp edge on whatever needs sharpening. Timeless Old World tech that still dazzles.

Over the course of two days I re-sharpened nearly a dozen old blades, including removing the secondary bevel on an old stainless Ontario saber-grind Navy diver's knife, convexing the edge on flat ground 1095 Schrade 55 that also came with a secondary bevel, and fixing a broken tip on an old Kershaw folder. These stones made quick work of the Schrade and Kershaw. Both had completely new edge geometry within 30 minutes apiece. The Kershaw looked like-new, as if the tip had never broken. And the Schrade cut much better than it's secondary bevel would previously allow, regardless of how sharp I got it with a ceramic rod and strops. The Ontario took a little more work, as it had been abused a little the last time I'd held it, over 25 years ago and was as dull as a case knife - one of the reasons I decided to go ahead and do a full saber grind - well, a slightly convexed saber, I suppose would be more accurate. But within under an hour of using the two stones and a couple leather strops (one with black compound, another with green), the Ontario was shaving sharp again too.
The truth is that there is no one recommendation that we can make that will meet everyone’s needs. Every sharpener’s needs are different and every sharpening toolkit will be different. In order to help beginning sharpeners get started with good sharpening stones to build around, we need to understand their individual needs. So with that in mind, let’s look at the basic needs of a beginning sharpener.
I really like this stone. The 1000/4000 grit combination is perfect for my needs. I'm a woodturner, and belong to a club that brings in professional turners from around the world. One had an eye opening test of sharpness. He stacked around 25 new razor blades in a box with one open side. The box assured that the blades were in perfect alignment. If you looked at the blades' sharp ends head on, all you saw was black. His point was that if you can see the edge, the blade is not sharp. Any reflection from the edge, again, facing it head on, is a dull spot. My long story leads to the fact that I was able to sharpen several knives to the point of not seeing the edge. This is not the stone to use if you are trying to remove nicks from a blade. A lower grit will do that job. This is for putting a fine, "invisible" edge on the blade, and with the right technique, that's what it will do. Another thing to consider is the fact that these stones are "sacrificial" A stone wears because it is deliberately giving up dull surface particles to expose the sharp ones below them. Anyone expecting a stone to last forever is mistaken. Bottom line? I think this is a great stone that takes my knives to the level of sharpness I need in both woodworking and cooking. I also like the rubber frame it sits in, giving you much better control over the stone. Your efforts can go into sharpening without having to steady the stone on your workbench or countertop.

100% Brand NewA fine-grained whetstone lubricated with oil, used for fine sharpening.The Ruby sharpening stone and Agate Stone,For Polishing,Sharpening.Can Make Mirror surface, mirror finish.The Ruby Sharpening stone is made from sintered crystals of synthetic ruby.It’s extremely hard, maintain their shape well and are resistant to wear.Size:50*25*10mm(1.97*0.98*0.39 inch)Model:3000 & 10,000 GritColor: red & whiteMainly used in industrial instrumentation, precision parts, miniature knives, stones, measuring tools, cutting tools, instruments, carbide, etc.Package included:1x Two Sides Jade SharpenerNote:Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error i.
Now you are going to use P2 pressure, moderate and in this case the stone is going to do the work, you are just guiding the knife along, stabilizing it as the amazing water stones does it’s job. Use the exact same technique, same angle but just moderate pressure, hardly pressing down at all, you are not trying to form a burr here, that is already done, now you refining the edge and bevel, removing some of the scratches left by your first stage of the process. Here is where the knife will get sharp and it will happen quickly. Now you are removing the burr, you are cleaning up the edge, some of that fatigued metal is going to want to hang on to the mother ship, your moderate pressure is going to start taking it away, as reluctant as it is to leave, it won’t have a choice. This should only take a couple minutes just mimicking the first step but with lighter pressure and this time visualizing the burr being scraped away, it will start to vanish.

A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.


Table mounted device – Typically the manual powered table mounted sharpener looks virtually identical to the electric powered sharpener with a slot for each stage. Where they differ is that each slot in the manual powered sharpener has only one groove and you pull the blade through this groove toward you to sharpen the blade. Once the blade is sufficiently sharp you place it in the honing groove to refine the edge and pull it toward you again several times. If there is a third, cleaning, stage you repeat the process for that stage as well.
As you see in the pictures, it is always very important to keep same angle of about 10' to 15', which is about two coins height between the blade and the whetstone. Gently push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures). Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade.
The company is to be commended for including links to instructional videos in the package. Those videos lay out clearly how to get the most from your Whetstone sharpener stone. Once you get up to speed you’ll likely enjoy the process and at the same time achieve professional quality results time and again. Sure, it’s not fancy and doesn’t have a sleek, chrome plated design but it works.

In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
×