I like the fact that there are two different grits (can be seen as two colors). the black rubber feet stick to the kitchen granite top like glue. The 1000 does a pretty good job of getting a knife roughly there and the 4000 puts on a fine polish for razor a sharp edge. I would go the extra step of stropping the knife after the grinding operation for an extra sharp edge.
Believe it or not the company have put a bit of effort into refining the look of their product to make it more aesthetically appealing. Whether or not they’ve succeeded we’ll let you decide. Once you get accustomed to the Classic II however the results are undeniable and the whole thing will make perfect sense. Use it on your kitchen knives, hunting knives, utility knives and more and enjoy the same high quality finish every time.
However, because the Belgian Blue stone generally occurs in relatively wide columns with much thinner layers of Vielsalm Coticule on either side adjacent to the slate, the Belgian Blue stone is more plentiful that Coticule and thus, it’s somewhat less expensive. But, it’s also somewhat softer than Coticule and is not divided into different grades as Coticule is. Furthermore, because it is a softer stone than Coticule, it is sold without a substrate layer.
Feedback is something that is very important to most sharpeners, i.e. how the stone feels when you are using it. Does it feel smooth, creamy and silky or does it feel hard and scratchy. While feedback, pleasant or unpleasant may be a purchase deterring factor it really doesn’t have any effect on level of sharpness that the stone can deliver. Unless of course the feedback is so distracting that it hinders the sharpeners focus and enjoyment and as a result, the sharpener doesn’t like what he/she is doing so that ultimately it does have the potential to negatively impact the results.
To take off the fine scratches and burrs left by coarser stones, and to polish the surface, you can use stones starting at around 2000 grit. There is theoretically no upper limit, but stones above about 10000 grit achieve practically no measurable improvement in the edge. It is also interesting to note that above 8000 grit, there is no Japanese measurement standard. For stones labelled as having a finer grit, you simply have to take the manufacturer's word for it.
Keep the stone submerged until the bubbles slow down or about 5 minutes then it's ready for use. Starting with the lowest grit which is 1000 on this stone, hold your knife at about a 15 degree angle and slide it away from you. It only takes light pressure along the strokes. You don’t need to push too hard. Gently slide from the tip to the base of the blade. After about 12 to 15 strokes, flip the blade over and repeat on the other side. Continue using gentle and even passes across the stone. Remember to hold the blade at about a 15 degree angle which is about half the height of your thumb. Keep the moves consistent and at the same speed.
Today, however, there is a whole new generation of mechanical sharpeners that are far more forgiving for those who may not use perfect technique. At the same time many more people have become accustomed to sharpening their knives this way and the average novice of 10 years ago is now the seasoned pro. It is still possible to damage knives with an electric sharpener, but you would have to either be trying to damage the knife or have some type of accident in order to do so.
first time buying a sharping stone. i bought this because i wanted to sharpen kitchen knives. you have to practice to get good at it, use a knife you don't care about because you might mess it up. there is some conflicting instructions online on how to use, water or no water. read as much as you can about using stones and practice, practice , practice. look up videos on youtube and internet. i had fun using it, BUY IF YOU WANT TO LEARN here is some stuff i found, they all sound like professionals http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 http://culinaryarts.about.com/od/knivescutlery/ht/whetstone.htm this is a video that says don't use water http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 this is a youtube video that i watched that uses water. *informative http://www.youtube.com/watch?v=KFIg9Cm-nJg
Frequently, our recommendation for beginning sharpeners is to start with diamond stones as their strengths make them ideal to build a sharpening toolkit around. Diamond stones are low maintenance and durable, lasting many years with only occasional cleaning. They are among the fastest stones to use making them time efficient. Diamond grit will handle even very hard steels, and diamond stones can be used for flattening waterstones. All these things make diamond stones a practical foundation for your sharpening toolkit.
Your primary goal is just to improve the edge, make it a little bit sharper. Manage you’re expectations and don’t worry about getting the knife ready for eye surgery on day one. Ignore all those YouTube videos where you see folks performing miracles with their knives, forget that completely. You just want to make the knife a little less dull and by doing so you will achieve what most people will never even attempt. You want to get a taste of sharpening success and it can happen quickly. If you are reading this, or any other cool sharpening tips, you’re on the right path.
A sharpening stone is a stone that has got a coarse side and usually a finer side, and that is going to take and re-shape your edge and get it back down thin enough in order to sharpen it. You are basically taking something that is blunt and thinning it back down. You have to remove all of this extra metal and get it back down to where it is thin enough to cut. Very simply, all a knife is is a very thin piece of steel to split whatever you are cutting. If the knife is obviously thicker, it is like trying to cut something with a chisel; it is not going to happen.
"How do I use this daunting metal rod?" I hear you ask. Well, it's not too hard, really. The best way for a beginner is to balance the steel on a surface with the tip secured by a damp tea towel. You want to get that angle right, whether it's around 15 degrees for a Japanese knife or 20 degrees on a German or French blade. Then swipe slowly down, away from you, making sure the whole blade is honed – around five swipes on each side should do.
Rest your knife on the stone at your chosen angle. An easy method for determining the angle by eye is to visualize a 45 degree angle and then take half that amount. That will give you a ballpark estimate of the angle and then you can adjust accordingly up or down. With a slicing action bring the length of the knife across the stone with a motion that starts with the heel of the knife on the stone and ends with the point of the knife. The motion should resemble a sweeping arc pattern across your stone. Be very careful to maintain the angle of the knife on the stone. Longer curved knives provide additional challenges but as long as you can maintain the angle you will be sharpening very effectively. Repeat this process on the other side of the knife and continue repeating until you have sharpened your knife though all your stone grits.
Your kitchen knife becomes dull when the metal at the primary edge, the cutting edge becomes fatigued and rolls over to one side or both sides of the blade. This is normal, it should happen regardless of the quality of the steel and what you are using the knife for. The difference will be “when” it gets fatigued, the better the steel the longer the edge will hold out, generally speaking. However, I have noticed something with high quality knives such as a Fujiwara and this may be applicable to you: I have several different brands of knives ranging from mediocre to my one dream knife. Theoretically, the mediocre knives with their mediocre steel should become dull faster under normal use. (I am referring to use at home, not in professional kitchen and not in the hands of someone who cuts lotus blossoms all day long)
I recommend keeping two stones in your kit. One with a medium grit (around 800 or so) to perform major sharpening jobs, and one with a fine grit (at least 2,000) to tune the edge to a razor-sharp finish. For real pros, a stone with an ultra-fine grit (8,000 and above) will leave a mirror-like finish on your blade, but most cooks won't notice the difference in terms of cutting ability.
This is a great sharpener for budget conscious cooks. You can use it with equal facility whether you’re right or left handed, it has a convenient finger guard to cut down on accidents and most important, it only takes a few swipes on a regular basis to keep your knives in tip-top condition. It’s not glamorous. It won’t add anything substantive to your kitchen decor. But it will ensure your knives are always ready for whatever dish you have in mind.
Oil Stones differ from water stones in that they require the use of honing oil to float the swarf (metal particles). Also, these stones are commonly made from one of three different materials consisting of Novaculite, Aluminum Oxide (Corundum), or Silicon Carbide (Carborundum) and they all use oil to lubricate the stone and suspend the swarf in order to prevent the stone from becoming clogged. Also, while Novaculite and Coticule are the most traditional types of oil stones, there are also synthetic oil stones made by the Norton abrasives company called “India Oil Stones”.
There are three key ingredients to a great cup of coffee: the right bean, the right brew, and the right grind. The Camano Coffee Grinder ensures you get the last one right every time. It has a cast iron top arch and hopper that works in conjunction with a ceramic burr to provide a precise, consistent grind. All that sits atop a wooden base, which attaches to a Ball Jar to hold the ground coffee, giving it an old-timey look while ensuring dependable performance for years to come. Made by hand, every component is also made in the USA.
When attempting to choose a whetstone for sharpening your favorite knife, the number of choices can be mind boggling. In fact, sharpening stones are divided into four distinct categories consisting of natural whetstones and manufactured whetstones which, in turn, are divided into two other categories consisting of oil stones and water stones. Then, there are numerous different varieties of natural whetstones consisting of several different materials that are quarried from different places around the world as well as several different types of man-made whetstones!
Serrated blades have a grind on one side of the blade. Only sharpen the grind side of the blade. Hold the sharpener at the angle that matches the original edge angle. Hold the knife with the edge away from you and the serrated side of the edge facing up. Set the tapered diamond sharpener in a serration so that you fill the indentation. Draw the sharpener towards the edge.
The smaller the angle between the blade and stone, the sharper the knife will be, but the less side force is needed to bend the edge over or chip it off. The angle between the blade and the stone is the edge angle – the angle from the vertical to one of the knife edges, and equals the angle at which the blade is held. The total angle from one side to the other is called the included angle – on a symmetric double-ground edge (a wedge shape), the angle from one edge to the other is thus twice the edge angle. Typical edge angles are about 20° (making the included angle 40° on a double-ground edge). The edge angle for very sharp knives can be as little as 10 degrees (for a 20° included angle). Knives that require a tough edge (such as those that chop) may sharpen at 25° or more.
Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
Start off on the rough grit side of the stone. Check the grit on your stone, or the packaging that came with the stone, to identify which is which. In general, whetstones and diamond stones each have different grits on either side. The rough grit side is used to grind the steel down, while the fine grit side is used to sharpen or hone the knife. The grinding process comes first, so you start on the rough grit side.
The most important aspect of a sharpening stone is the grit. If you have knives that have taken a beating and are either nicked up or really dull, you’ll need a courser stone to get it back into shape. And in order to put an exceptionally sharp edge on an already sharp knife, you’ll need a finer grit stone. If your knives are already in pretty good shape and just need a touch up, buying just a finer grit stone might be enough, but don’t think you can get away without a courser stone for knives that need more TLC. It is possible to buy a combination, or two-sided sharpening stone.
Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.