All rights reserved. WARNING - Under the Liquor Control Reform Act 1998 it is an offence to supply alcohol to a person under the age of 18 years (Penalty Exceeds $17000). It is an offence for a person under the age of 18 years to purchase or receive liquor (Penalty exceeds $700). This web site is operated by Chef’s Armoury. ABN 62 001 477 014. Liquor Licence 36129161.
All stones require either water or oil as a lubricant to sharpen the knife. We prefer water stones because they’re easier to use, less messy and don’t have the possibility to go rancid like oil does. If you choose a water stone, all you have to do is either add water to the stone before placing the knife on the surface, or soak the stone in water for 10 minutes before use. You’ll want to read the instruction for the stone you purchase to find out how to use it properly.

Once you've sharpened one side, you need to flip over, but don't swap the hand gripping the blade – think of it a bit like going backhand with a tennis racket (see above). Lead with the heel this time, rather then with the blade, but repeat the process in three parts. After five strokes on each third of the blade, it's time to check your knife. It's not an exact science, and it all depends on how blunt your blade was to start with (mine was very blunt indeed). But if you sharpen fairly regularly, it should just take a few strokes. 
"How do I use this daunting metal rod?" I hear you ask. Well, it's not too hard, really. The best way for a beginner is to balance the steel on a surface with the tip secured by a damp tea towel. You want to get that angle right, whether it's around 15 degrees for a Japanese knife or 20 degrees on a German or French blade. Then swipe slowly down, away from you, making sure the whole blade is honed – around five swipes on each side should do. 

I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
×