You must put the knife blade's position at the perfect angle which is called "against the stone." What's important is the blade should be facing opposite from you. Where you've determined where the bevel angle is located, then this is what you will position against the stone. It's a good idea to know the differences between various angles for certain blade uses. There's a certain height of the blade that it should be from the stone. You'll be able to find various charts on height of the blade online. Normally, for a pocket knife or kitchen knife, it'll be 17° - 22° angle against the stone. The "Rule of thumb" is the smaller the angle, the sharper the knife. Most makers will have it in the instruction or on their official website.
I've only used it to touch up the edge on an ESEE RB3 and a pocket folder so far, but it has done very nicely for those tasks. I found that using the rounded edge works best for me in order to be able to run the length of the blade without hitting the leather lanyard. I'll hopefully try it out soon on fish hooks, too. A worthy and handy accessory, and cool looking necklace, to boot!
Serrated blades have a grind on one side of the blade. Only sharpen the grind side of the blade. Hold the sharpener at the angle that matches the original edge angle. Hold the knife with the edge away from you and the serrated side of the edge facing up. Set the tapered diamond sharpener in a serration so that you fill the indentation. Draw the sharpener towards the edge.
When attempting to choose a whetstone for sharpening your favorite knife, the number of choices can be mind boggling. In fact, sharpening stones are divided into four distinct categories consisting of natural whetstones and manufactured whetstones which, in turn, are divided into two other categories consisting of oil stones and water stones. Then, there are numerous different varieties of natural whetstones consisting of several different materials that are quarried from different places around the world as well as several different types of man-made whetstones!
Ceramic sharpening stones were the early replacement for natural stones. Unfortunately there are huge differences in the quality of ceramic stones so be wary. Some are extremely soft and dish out very quickly and at the other end of the spectrum some are so hard they tend to glaze over in a hurry. Ceramic stones need a good soaking for about 10 or more minutes to saturate the pores of the stone prior to use. As all knife steels are different we tend to find that ceramic stones tend to work better with some knives over others. There are no hard and fast rules but we like ceramic for Ao-ko and single edged knives. The Kaiden Ceramic stones are the fastest cutting Japanese stones in Australia and are recommended for advanced users.
Honing is kind of like dusting the furniture while sharpening is more like reupholstering the furniture. Honing is purely a maintenance activity that should be regularly practiced to make sure the blade is clean and sharp as can be every time you use it. It’s easily done using a honing rod, a leather strop or a sharpening stone; as most stones have a side for sharpening and a side for honing. Honing is akin to trimming your hair to remove the split ends. It’s not a full on haircut. What it does is realign the tiny sharp protrusions along the edge of the blade that can be bent over with use, so that they stand more or less straight.
To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.
Diamond sharpening stones are becoming really popular because of their ability to cut fast. We tend not to recommend diamond sharpening stones/plates because a lot of damage can be done very quickly. Also diamonds are pretty sharp and at arato level they leave deep scratches in the blade that need to be polished out quite aggressively. Diamond stones can be used with and without lubricant.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
Last, it should be noted that dual-sided Coticule/Belgian Blue whetstones are also sometimes available which have a layer of Belgian Blue stone on one side and a layer of Coticule on the other. Thus, these whetstones provide a softer, more coarse, grit on one side and a harder, finer, grit on the other. Plus, due to the inherent toughness of the Belgian Blue stone, these dual-sided stones do not require a substrate layer.