Now you are going to use P2 pressure, moderate and in this case the stone is going to do the work, you are just guiding the knife along, stabilizing it as the amazing water stones does it’s job. Use the exact same technique, same angle but just moderate pressure, hardly pressing down at all, you are not trying to form a burr here, that is already done, now you refining the edge and bevel, removing some of the scratches left by your first stage of the process. Here is where the knife will get sharp and it will happen quickly. Now you are removing the burr, you are cleaning up the edge, some of that fatigued metal is going to want to hang on to the mother ship, your moderate pressure is going to start taking it away, as reluctant as it is to leave, it won’t have a choice. This should only take a couple minutes just mimicking the first step but with lighter pressure and this time visualizing the burr being scraped away, it will start to vanish.
Selecting the proper coarseness for your sharpening stone is an important first step in sharpening your knife. Not every knife needs to start at the coarsest stone you have, on the other hand a very dull knife can not be sharpened on only your finest stone. Starting with the proper coarseness will ensure that you achieve the edge you need quickly. If your knife is very dull or has a nicked blade, start with your coarsest stone. The coarse stone removes material quickly so a poor edge can be refined quickly. However, the coarse stone must be followed up with your finer stone to refine the edge. If your knife is only slightly dull and just needs a quick touch up, starting at a medium or fine stone can save you time. Starting on a fine stone requires fewer steps but must only be used on an edge requiring little work.
Removing the burr is fairly simple. You'll need a leather strop or block (this sort of thing), which is designed to catch the metal fibres from the knife. You could do it with a fibrous tea towel or some newspaper if you like, but I'd suggest going with leather to begin with. The motion is fairly similar to sharpening. Draw the knife over the leather, going away from the edge at roughly the same angle as when you sharpened.
However, because the Belgian Blue stone generally occurs in relatively wide columns with much thinner layers of Vielsalm Coticule on either side adjacent to the slate, the Belgian Blue stone is more plentiful that Coticule and thus, it’s somewhat less expensive. But, it’s also somewhat softer than Coticule and is not divided into different grades as Coticule is. Furthermore, because it is a softer stone than Coticule, it is sold without a substrate layer.
The composition of the stone affects the sharpness of the blade (a finer grain, usually, though not always, produces sharper blades), as does the composition of the blade (some metals take and keep an edge better than others). For example, Western kitchen knives are usually made of softer steel and take an edge angle of 20–22°, while East Asian kitchen knives are traditionally of harder steel and take an edge angle of 15–18°. The Western-style kitchen knives are generally in the range of 52–58 on the Rockwell scale, which denotes the relative hardness of a material.
When you apply a sharp knife to the surface of a tomato, cucumber, carrot or other food item it should - if you are holding it firmly and applying minimal pressure - sink into the particular item without effort. As such all you really need to work on is your technique and making sure you keep your fingers out of the way. With a dull knife however things aren’t quite so simple. When you apply a dull blade to, say, a tomato it’s not going to slice into the skin. Instead the skin will be able to push back meaning you’ll need to apply ever more pressure to get the knife to penetrate. Increasing the pressure on the knife increases the likelihood of the knife slipping off the offending food item to one side or another. And if it slips to the side where your hand is attempting to hold the vegetable steady you could be in store for a very nasty cut. Because even a dull knife will cause injury if there’s enough force behind it.
There will be a drawer that extends into the mechanism under the abrasives. Any detritus from the sharpening process drops into this drawer. Exactly where the drawer is located will differ from sharpener to sharpener but it shouldn’t be hard to find. Remove the drawer flick any material into the wastebasket and then wipe out the drawer with a damp cloth or tissue. You may want to use work gloves and goggles to protect your hands and eyes from any loose metal shavings. Once the drawer is clean and dry replace it. The exact means by which the sharpening mechanism itself is cleaned will vary from manufacturer to manufacturer. Consult your owners guide for specific details. Make sure you don’t introduce any grease or other lubricants into the sharpener unless specifically directed to do so by the owner’s manual. Also, the outside of the sharpener should come perfectly clean with just a damp cloth. Avoid using commercial cleaners or abrasives of any kind.
Our large selection of stones from many well-known manufacturers will allow connoisseurs to find the ideal stone for their needs. Because all manufacturers formulate their stones to emphasize a different mix of qualities, and because these qualities can vary widely between different stones, most woodworkers choose stones from several manufacturers to build up an optimal set of sharpening stones. Then again, once you get to know the characteristics of certain types of stone, you may find one supplier who will provide all the stones you need. Sometimes this can be an advantage. But there is no one size that fits all; each stone must fit your needs and work style.