When the block is intended for installation on a bench it is called a bench stone. Small, portable stones (commonly made of bonded abrasive) are called pocket stones. Being smaller, they are more portable than bench stones but present difficulty in maintaining a consistent angle and pressure when drawing the stone along larger blades. However, they still can form a good edge. Frequently, fine grained pocket stones are used for honing, especially "in the field". Despite being a homophone with wet in most dialects of modern English, whetstones do not need to be lubricated with oil or water, although it is very common to do so. Lubrication aids the cutting action and carries swarf away.
Sharpal 102N 5-in-1 Knife and Hook Sharpener features Sharpal 102N 5-in-1 Knife and Hook Sharpener features pre-set crossed carbides for quick edge setting and ceramic stones for fine honing. Multi-groove sharpening stone is designed to sharpen fishhooks of various sizes. It comes with rubber over-molded body and feet for secure and comfortable grip. Moreover integrated compass built-in rust-proof ... More + Product Details Close
A base for your whetstone should be included in any model you purchase. Considering you are using your whetstone after its been submerged in water; the stone tends to slide on most surfaces when you sharpen. The base, usually a rubber silicone anchor, will ensure that the stone does not move around. A slippery stone can be a hazardous situation. The goal is safety, however, some companies will take liberties to present a decorative base and forgo the safer option.
A good whetstone and a little practice will keep all of your knives sharp and in perfect condition. The beauty is that it doesn’t take much effort to learn, just a good bit of practice to get the angle right and keep a consistent angle while you’re sharpening. Whetstones are available in department stores or online, and while they range in price based on the fineness of the grit, this thread at eGullet can help you pick a good grit to start with.
If you’re sharpening high quality knives, you probably don’t want to use a cheapo sharpening stone. But if you’re just getting started with sharpening your pocket knife, there’s no need to get too fancy right off the bat. You can find a sharpening stone at most hardware stores for about $10. This one is very similar to the one I use. Nothing fancy. Most basic sharpening stones come with two sides: a rough grit and a fine grit. The finer the grit, the finer or sharper you can get your blade. You usually start off sharpening on the rough grit and then finish sharpening it on the finer grit.
Hobby microscope view of a 220 grit diamond sharpening stone. Tiny diamonds are electroplated to a perforated metal carrier strip and bonded to a plastic backing. The feature identified with the red line across it measures about 0.08 mm across. The dark area at upper right is a void designed to allow for swarf created during sharpening to be cleared from the diamonds. This relatively coarse stone would be used to reshape a damaged blade edge which would be refined by finer grit stones.
Don't know. Not sure that I really care, as these stones definitely did the job that was asked of them, and did it with ease, even for a beginner whetstone user. I'll probably stick with them, at least until I get a lot more experience. Though, I do see a 10,000 or higher grit stone in my immediate future - more to play around with, than a feeling of genuine need.
Chefs will do this every day, and there's no reason you shouldn't too. Before cooking, or after you've done the washing up, honing your knife will help keep it in good condition. "When you're using a honing steel, you're not actually removing any metal at all, just re-straightening that edge, to get it back in line," says Authbert. Remember that you'll still need to sharpen it every two or three months.
4. Start sharpening the first side of the blade. With your blade set at the prefect angle, you’re ready to start sharpening. Imagine you’re carving off a slim piece of the stone’s surface. Personally, I bring the blade into the stone. Other people stroke the blade away from the stone. Both ways work, so just use whatever technique you prefer. If the knife blade is curved or if it’s longer than the stone, you’ll need to sweep the blade sideways as you work, so the entire edge is sharpened evenly. Apply moderate pressure as you sharpen. No need to bear down hard on the blade. After you make one stroke, start back at the beginning and repeat. Do this about 6-12 times.