Novaculite is a type of stone that can only be found in North America and in a limited geographical region of Texas, Oklahoma and Arkansas. The novacula stone formation in the Ouachitas of Central Arkansas is geologically considered, without a doubt, to be the purest and finest quality.  Its extremely high-purity silica content exceeds 99 percent. This Ouachita Mountain Novaculite is the only Novaculite we use in producing the FINEST whetstone sharpeners you can buy.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..

Basically, there are 3 types of whetstones, Arato (rough grits), Nakato (medium grits) and Shiageto (fine grits). We normally use Nakato for the sharpening, but you can start with Arato to correct rough or damaged edge, and then Nakato and finish with Shiageto to get a fine and keen edge. All the sharpening methods and processes are same. However, it is not recommended to sharpen the opposite flat side of the blade with Arato


Sharpal 102N 5-in-1 Knife and Hook Sharpener features Sharpal 102N 5-in-1 Knife and Hook Sharpener features pre-set crossed carbides for quick edge setting and ceramic stones for fine honing. Multi-groove sharpening stone is designed to sharpen fishhooks of various sizes. It comes with rubber over-molded body and feet for secure and comfortable grip. Moreover integrated compass built-in rust-proof ...  More + Product Details Close
A DUAL FUNCTIONING BLOCK This carefully designed tool is actually two stones in one. When deciding on the perfect wetstone knife sharpener, you want a rock that has a lower-numbered grit for sharpening and a higher-numbered grit for polishing. One side of our stone is #1000 and is designed to sharpen dull blades with accuracy and precision. The other side is #6000 and provides a deluxe polishing effect. Our aluminum sharpening stone ensures optimal performance of your knives.
Your whetstone will most likely be double-sided with a coarse and a fine grit. The grit is determined by the number of sand-like particles in the stone. The coarse grit will have fewer particles, whereas the finer grit will have more grains. Both sides are utilized to effectively sharpen a blade. The coarse grit, usually a deeper color; red or gray, will pre-sharpen the blade and remove any burrs or discrepancies in the blade. The finer grit is then used to hone and polish the blade, creating a finished edge.
Be careful: Don’t move your fingers laterally along the edge, you’ll cut yourself. Feel for a rough area running from tip to heel. Again, it takes time to know what to expect because the best burr will be subtle. Just know that the bigger the burr, the more metal you are removing—more than necessary. Don’t worry, you won’t ruin the knife doing this. You’re learning here, and mistakes are part of the sharpening journey. Learn from them.
A wide selection of high-quality knives from well-known brands such as Morakniv and Stanley as well as our own brand, Cocraft. Here you'll find tool knives for most kinds of jobs. Knives for tradesmen, craftsmen, fishermen, campers and many more. A high-quality range of knives is the Morakniv series of sheath knives made in Sweden, which have either stainless steel blades or carbon steel blades, a material, which is easily sharpened. Our work knife range includes various specialised knives for different tradesmen, carpet knives, utility knives, craft knives, penknives, folding knives and rotary cutters. Regardless the type of knife, a blunt blade is both inefficient and dangerous. With a whetstone, sharpening steel or knife sharpener, you'll be able to keep a keen edge on your blade and ensure that your tools are always ready for use. Some knives, such as snap-off blade knives and utility knives don't need sharpening. They take disposable blades, which of course we sell replacements for.
After several uses the Kamikoto is proving itself to be better than expected. As a professional I use different knives all the time and in fact have several thousand dollars worth of very fine blades of various manufacture. As it stands right now, if I could pick only one knife from all of them, I would take the Kamikoto. Fish, vegetables, raw meat, cooked meat, it handles them all very well and is a pleasure to use because of excellent balance and weight. And the edge… magnificent. Care and careful sharpening will be important, but then it always is with the finest of things. I would unhesitatingly recommend this product to people who appreciate the best. This is not a knife for fools or clumsy people. Buy, use, enjoy. And to the people at Kamikoto; “Thank You for making such a beautiful thing!”
MADE OF THE FINEST MATERIALS This durable knife polishing stone is a high-performing, industrial grade product designed for chefs and all of us who think we are chefs. The combination whetstone is double sided, premium quality corundum which is a rock-forming mineral derived from aluminum oxide. While most sharpening sets use bamboo or wood stands, our products comes in a slick, sturdy, aerated box with holes at the bottom so it won’t warp or crack due to moisture.
TO USE: Soak stone in water for no more than 5-10 minutes. Place stone on a damp cloth with the courser 400 grit side (dark green) facing up. Hold the knife so that it’s flat and perpendicular to the block, with the blade facing left. Holding the knife at a 20-degree angle, slowly sweep the edge of the blade from left to right down the length of the stone and continue until sharp. If stone starts to feel too dry, add more water. Be patient and take your time. Flip knife over and repeat on the other side (now moving from right to left). Be sure to sharpen both sides evenly. To polish the blade further, flip stone over to the fine 1000 grit side (light green) and repeat the process. When blade is honed to desired sharpness, wash and dry your knife. To clean your stone, simply rinse with water, wipe away any remaining metal residue with a rag, rinse again, then dry.
My order came in incomplete. I contacted the company and had a response within a couple hours. They immediately responded, researched and started the replacement process. I had my order replacement within 1 week or so. Every email was answered the same day. I so highly recommend this company. LOVE MY PRODUCT AND LOVE THE SERVICE MORE. GREAT COMPANY.
From the moment I ordered the knife set, I was emailed every step of the way till they were delivered. When I opened the box I instantly knew I made the correct decision. The weight, balance and edge were perfect. A few of my friends have handled them as well and all have asked the same question. How can I get these. I highly recommend these knives.
Once you've sharpened one side, you need to flip over, but don't swap the hand gripping the blade – think of it a bit like going backhand with a tennis racket (see above). Lead with the heel this time, rather then with the blade, but repeat the process in three parts. After five strokes on each third of the blade, it's time to check your knife. It's not an exact science, and it all depends on how blunt your blade was to start with (mine was very blunt indeed). But if you sharpen fairly regularly, it should just take a few strokes. 
We begin our whetstone sharpening process with a 400 grit stone to shape the edge of the blade and develop a burr along the edge of the knife. Once the shape is set and we have a burr along the full length of the knife we move on to the 1000 grit stone to refine the edge and begin removing the burr, followed by the 5000 grit fine stone stone to give a beautiful sharp edge on the blade. We finish off each knife on a leather stropping block which removes the final remnants of the burr and gives a strong and lasting edge.

Crafted by employing methods from centuries-old traditions, the Kamikoto Toishi Sharpening Whetstone is specifically primed to hone and sharpen single bevel Japanese steel knives. The sturdy bamboo stand has been formed to hold the whetstone firmly in place during the entire sharpening process, allowing for the control necessary to form the perfect chiselled edge. The Toishi Sharpening Whetstone features two sides with different grits; the 1000 grit side is the coarser side, utilized specifically to grind away at the rougher edge produced over multiple uses of a knife. The other side consists of a finer 3000 grit for polishing and finishing the edge of a blade, the final step in a sharpening cycle.
Begin with your lower-grit stone. Place the heel of your knife on the far edge of the stone, holding the blade gently but firmly with both hands at a 15- to 20-degree angle. Using even pressure, slowly drag the knife over the stone toward you down the length of the stone while simultaneously moving the knife such that the contact point moves toward the tip of the blade.
J. Kenji López-Alt is the Chief Culinary Advisor of Serious Eats, and author of the James Beard Award-nominated column The Food Lab, where he unravels the science of home cooking. A restaurant-trained chef and former Editor at Cook's Illustrated magazine, his first book, The Food Lab: Better Home Cooking Through Science is a New York Times Best-Seller, the recipient of a James Beard Award, and was named Cookbook of the Year in 2015 by the International Association of Culinary Professionals.
These are unquestionably great starter stones. After all the sharpening done over the course of a couple days, they're still perfectly flat, showing little to no signs of wearing down. Mind you I did watch tons of how-to videos online before undergoing the endeavor, so I knew how to try to make the stone wear evenly. But, my 15 year old nephew who was working on the Ontario, as I told him he could have it, if he wanted to fix it up, didn't watch all those videos and I didn't see any uneven wear on his stone after working it about a half hour either.
After several uses the Kamikoto is proving itself to be better than expected. As a professional I use different knives all the time and in fact have several thousand dollars worth of very fine blades of various manufacture. As it stands right now, if I could pick only one knife from all of them, I would take the Kamikoto. Fish, vegetables, raw meat, cooked meat, it handles them all very well and is a pleasure to use because of excellent balance and weight. And the edge… magnificent. Care and careful sharpening will be important, but then it always is with the finest of things. I would unhesitatingly recommend this product to people who appreciate the best. This is not a knife for fools or clumsy people. Buy, use, enjoy. And to the people at Kamikoto; “Thank You for making such a beautiful thing!”
×