Now you may wonder, if a finer stone produces a better cutting edge why do I need a coarse stone at all? The answer is that finer stones work much more slowly than coarse ones. The amount of metal a fine stone removes with each pass is much less than what a coarse stone removes. If you have an edge with a good shape to it from a coarse stone, this is not a problem because the fine stone doesn’t have to remove much metal to improve the edge. If the edge is dull, it will take many times longer to reshape it with a fine stone than it would with a coarse one.
An extremely well written and informative article on sharpening. Overtime we all get to love certain stones for our sharpening needs. I am a huge coticule fan, and although i have used all the others, i always come back to this natural stone above all others. Still trying to figure if i chose it or it chose me! NEver the less there are so many options out there it is not hard with a little time and effort to find the right combination for your needs.
The following are my personal favourites and they are all synthetic stones, I do have experience with natural what stones but lets keep it simple, lets stick to synthetic water stones. Believe me, some of the world sharpest knives are sharpened solely on synthetic stones. Here are my personal favourites, I use these water stones every day and the order is not necessarily in priority, they are all good.
The Chef’s Choice 476 2-Stage Sharpener transforms your weary kitchen, hunting and pocket knives into razor sharp cutting instruments with dependable ease. The sharpener is simple in concept, solid in its fabrication and reliable in the way it goes about its business. The design is also free of right-hand bias which is good news for the lefty chefs out there.
A: When it comes to the best knife sharpeners used in a domestic setting the abrasives used to sharpen the blade should last for quite a few years. When they do eventually wear out many of the best manufacturers will refurbish them for you, typically for a nominal fee. Again, however, unless you are using the sharpener on a daily basis (and there is virtually no reason the average person would do this), the sharpener should last for many years before ever needing service.
Very handsome and functional. The leather that makes up the necklace is high quality and the knot they use is seldom seen. I was able to touch up my bark River gunny sidekick with it( m4 steel at 62-64 hrc!), And that is saying something. Haven't tested the fish hook groove, because I don't generally fish in the winter, but I'm looking forward to trying it out
Practice holding the knife at a 20 degree angle. Most straight blades need to be sharpened at a 20 degree angle. To find the angle, hold the directly in front of you so it's straight up and down. This is 90 degrees. Tilt the knife halfway towards the table so it's at a 45 degree angle. Tilt the knife halfway again so it's about an inch (2.5 cm) above the table. This should be a 20 degree angle.
All stones require either water or oil as a lubricant to sharpen the knife. We prefer water stones because they’re easier to use, less messy and don’t have the possibility to go rancid like oil does. If you choose a water stone, all you have to do is either add water to the stone before placing the knife on the surface, or soak the stone in water for 10 minutes before use. You’ll want to read the instruction for the stone you purchase to find out how to use it properly.
Removing the burr is fairly simple. You'll need a leather strop or block (this sort of thing), which is designed to catch the metal fibres from the knife. You could do it with a fibrous tea towel or some newspaper if you like, but I'd suggest going with leather to begin with. The motion is fairly similar to sharpening. Draw the knife over the leather, going away from the edge at roughly the same angle as when you sharpened.
Sharpening is really two processes: Grinding and honing. Grinding is simply the removal of metal. Honing is a precision abrasion process in which a relatively small amount of material is removed from the surface by the means of abrasive stones. Once you have the right shape, usually using a more aggressive grit, you then switch to a finer grit to hone the edge.
Whichever method you choose, be it a waterstone (also known as a whetstone), or a pull-through (either V-shaped or ceramic wheels) it's important to regularly hone your knife with a honing steel, which we'll also cover below. You'll be pleased to hear that you won't have to reach for the stones too regularly – once every two or three months should suffice.
For this type of hand held manual sharpener the 463 does an extraordinary job thanks mostly to the diamond abrasive wheels. You get an edge that’s both razor sharp and burr-free, as if you spent an hour working the edge on an oil stone. If people make a mistake with the 463 it’s that they assume more pressure is needed than actually is. Keep in mind though that it really shines on serrated and straight edged, double bevel Asian-style knives.
Hi Caide, our most popular stone at the moment is our Grunwerg 1000/3000 grit whetstone from speaking to our customers it’s definitely down to the pretty competitive price, but also they have said that the finish on the knife is just as good as some of our more expensive ones, the main difference is it doesn’t seem to last as long. For one that does last and leave a good finish then our Minosharp 1000 grit whetstone is also popular.
Why, then, do so many of us shy away from the task? To put it bluntly, it's because it's a rather daunting process for the beginner. Your image of knife sharpening may consist of a hyper-masculine chef slashing away violently at a steel rod (we're looking at you, Gordon). Conversely, you might have seen cooks meticulously and methodically stroking their blade up and down a Japanese waterstone with more intricate attention to detail than a Flemish landscape.
I can personally verify that this will get your knives very sharp. I will spare you all the gory details, but the picture is of the instructions the ER sent me home with after stopping the bleeding and patching me up. I have to say, that’s not what I had in mind regarding “Thanksgiving tips”. So: not only will knives slide easily through spinach, but they will go through finger and fingernail like a hot knife through butter after being sharpened by this whetstone. Very clean, straight cut. Impressive, really. Just take it slow and don’t be a moron like me.
first time buying a sharping stone. i bought this because i wanted to sharpen kitchen knives. you have to practice to get good at it, use a knife you don't care about because you might mess it up. there is some conflicting instructions online on how to use, water or no water. read as much as you can about using stones and practice, practice , practice. look up videos on youtube and internet. i had fun using it, BUY IF YOU WANT TO LEARN here is some stuff i found, they all sound like professionals http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 http://culinaryarts.about.com/od/knivescutlery/ht/whetstone.htm this is a video that says don't use water http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 this is a youtube video that i watched that uses water. *informative http://www.youtube.com/watch?v=KFIg9Cm-nJg
In most cases, the sharper, the better. The sharpness of your edge is determined by the angle (the lower the angle, the sharper the edge) and how fine of a grit you choose for your final honing. Since you have already determined your angle many steps earlier, now you just need to know which grit you can stop at. This again depends on the use of the knife. In most cases, go all the way to the finest stone that you own as this will give you your best edge. The only exception would be a knife used to cut soft vegetables like tomatoes, as a slightly more coarse edge will provide more of a tooth pattern for easier cutting.
Select the grit of the stone. Sharpening stones are available with different grit sizes. For example, you can choose fine, medium and coarse stones. You should use a coarse stone followed by a fine grit if your knives are dull. If your knives have been sharpened recently or they aren't too dull, consider using a medium grit. Try to use a grit level ranging from 325 (for coarse) to 1200 (for extra fine).
Cost – While you can get a perfectly serviceable sharpening stick or stone sharpener for short money and some very high-quality tabletop manual 2 and 3-stage sharpeners for less than $50, high-quality mechanical systems will often run you $200 or even more. While that’s not so much money it’s likely to impact the quality of your life it is a lot to pay to keep a decent edge on your knives. While how much you ultimately pay for a sharpener is entirely up to you, you may want to consider your commitment to cooking and how often you are actually liable to use the device. If this is your first sharpener you might also want to consider learning how to sharpen a blade using a classic stick or stone sharpener first, before deciding if moving up to a mechanical sharpener is the right thing for you.
Method 1: Use an Electric Sharpener. Quality electric sharpeners are an option, but I strongly discourage their use. First off, they remove a tremendous amount of material from your edge. Sharpen your knife a dozen times, and you've lost a good half-centimeter of width, throwing it off balance, and rendering any blade with a bolster (i.e. most high-end forged blades) useless. Secondly, even the best models provide only an adequate edge. If you don't mind replacing your knives every few years and are happy with the edge they give you, they'll do the trick. But a much better choice is to...
These are very popular stones. 8" Dia-Sharps have a single grit per stone making them more expensive, but at 8" by 3" they are wider than the 8" DuoSharps, offering a good working surface. The 8" Dia-Sharp line also has the widest range of grits available from DMT, with extra extra coarse, medium extra fine and extra extra fine options not available in other sizes, so it is good line to consider. One coarse and one fine stone is a good starting point.
Your task as a sharpener is to remove that fatigued metal and expose the steel underneath, the fresh strong steel and bring side A and B of the knife together at the Apex precisely, sounds easy doesn’t it? Like peeling a layer off and having a fresh start, over and over. Of course there is much more to it than this but in very basic terms, you want the abrasive properties of the water stone to abrade the fatigued metal away, like an eraser.
I enjoy these stones so much that the feedback is not a deterrent at all for me, I don’t even think about it. The results are always nothing but top notch, they deliver exactly what I want, some of the sharpest knives I have ever produced were sharpened on Shapton Glass stones. They may be thinner but they last a very long time, they are easy to maintain as well,
All rights reserved. WARNING - Under the Liquor Control Reform Act 1998 it is an offence to supply alcohol to a person under the age of 18 years (Penalty Exceeds $17000). It is an offence for a person under the age of 18 years to purchase or receive liquor (Penalty exceeds $700). This web site is operated by Chef’s Armoury. ABN 62 001 477 014. Liquor Licence 36129161.
Over the course of two days I re-sharpened nearly a dozen old blades, including removing the secondary bevel on an old stainless Ontario saber-grind Navy diver's knife, convexing the edge on flat ground 1095 Schrade 55 that also came with a secondary bevel, and fixing a broken tip on an old Kershaw folder. These stones made quick work of the Schrade and Kershaw. Both had completely new edge geometry within 30 minutes apiece. The Kershaw looked like-new, as if the tip had never broken. And the Schrade cut much better than it's secondary bevel would previously allow, regardless of how sharp I got it with a ceramic rod and strops. The Ontario took a little more work, as it had been abused a little the last time I'd held it, over 25 years ago and was as dull as a case knife - one of the reasons I decided to go ahead and do a full saber grind - well, a slightly convexed saber, I suppose would be more accurate. But within under an hour of using the two stones and a couple leather strops (one with black compound, another with green), the Ontario was shaving sharp again too.
Cut a wine cork so that it measures .5 of an inch and use that as your visual guide. You can keep it at the end of your water stone and rest the spine of the knife on it so that you can see what that angle looks like. Now this is all pretty nifty but you still have to learn to move that knife over the water stone holding it at that angle, whether you chose 20 or 15 deg, making the template is the easy part, stabilizing that angle is where practice is crucial. You can hold the knife with that wine cork in place and that is the angle you want sharpen at but now that piece of cork has to go, you’re on your own. I have taught many many people to sharpen a knife and believe me, this particular part of the process is not as hard as many people believe! In fact as you start actually sharpening the knife you will become quite motivated to succeed because it isn’t as hard as you thought it would be. In time, you’ll learn that you don’t need or want to sharpen everything at 20 deg, but for the sake of building muscle memory it is a good place to start.
In recent years, some whetstone manufacturers have started producing ceramic whetstones made from hard, ceramic, powders that are mixed with Aluminum Oxide and then sintered to form a solid. But, rather than using oil or water to lubricate the whetstone, ceramic whetstones are meant to be used without lubrication and thus, they provide a significant advantage for chefs who need to keep their knives sharp but, who do not have either the room or time for using a bench water stone. Thus, they are commonly available as either bench stones, pocket stones, round rods, or triangular rods.
Believe it or not the company have put a bit of effort into refining the look of their product to make it more aesthetically appealing. Whether or not they’ve succeeded we’ll let you decide. Once you get accustomed to the Classic II however the results are undeniable and the whole thing will make perfect sense. Use it on your kitchen knives, hunting knives, utility knives and more and enjoy the same high quality finish every time.
A: That depends almost entirely on how often you use them. If you are a professional chef who uses his or her knives every day then you should hone them every time you use your knives. But honing has its limits and over time your edge is going to become dull no matter what. Therefore your knives will need to be sharpened at least several times a year. Some chefs, in fact, will use a whetstone on an almost daily basis in order to ensure their knives are always razor sharp. Most of us, however, are not professional chefs and may not even touch our kitchen knives for days at a time. In that case, it’s probably a good idea to hone the edge after every couple of uses and have your knives sharpened once a year.