This is a great sharpener for budget conscious cooks. You can use it with equal facility whether you’re right or left handed, it has a convenient finger guard to cut down on accidents and most important, it only takes a few swipes on a regular basis to keep your knives in tip-top condition. It’s not glamorous. It won’t add anything substantive to your kitchen decor. But it will ensure your knives are always ready for whatever dish you have in mind.

Hobby microscope view of a 220 grit diamond sharpening stone. Tiny diamonds are electroplated to a perforated metal carrier strip and bonded to a plastic backing. The feature identified with the red line across it measures about 0.08 mm across. The dark area at upper right is a void designed to allow for swarf created during sharpening to be cleared from the diamonds. This relatively coarse stone would be used to reshape a damaged blade edge which would be refined by finer grit stones.
I really like this stone. The 1000/4000 grit combination is perfect for my needs. I'm a woodturner, and belong to a club that brings in professional turners from around the world. One had an eye opening test of sharpness. He stacked around 25 new razor blades in a box with one open side. The box assured that the blades were in perfect alignment. If you looked at the blades' sharp ends head on, all you saw was black. His point was that if you can see the edge, the blade is not sharp. Any reflection from the edge, again, facing it head on, is a dull spot. My long story leads to the fact that I was able to sharpen several knives to the point of not seeing the edge. This is not the stone to use if you are trying to remove nicks from a blade. A lower grit will do that job. This is for putting a fine, "invisible" edge on the blade, and with the right technique, that's what it will do. Another thing to consider is the fact that these stones are "sacrificial" A stone wears because it is deliberately giving up dull surface particles to expose the sharp ones below them. Anyone expecting a stone to last forever is mistaken. Bottom line? I think this is a great stone that takes my knives to the level of sharpness I need in both woodworking and cooking. I also like the rubber frame it sits in, giving you much better control over the stone. Your efforts can go into sharpening without having to steady the stone on your workbench or countertop.
This wedge ends up short of a "point" to a much larger degree than the picture would indicate. The metal stops short, but then there is black non-slide "tape" applied to one side, and white "slide" tape applied to the other side, which makes the wedge even thicker than it appears in the photo, which means that in practice the end of wedge is even more truncated. So I have a hard time supporting my knives accurately on this wedge while sliding them down into contact with my stones. Prior to buying this wedge I just used a wooden wedge I cut off of a 3" by 3" post using a miter saw, said wedgewhich has a much less truncated end. That wooden wedge unfortunately absorbs water from my Japanese Waterstones. But I will try spraying polyurethane on that wooden wedge to help waterproof itand try again. If that doesn't work I will try to find a 3" by 3" plastic trim board somewhere and cut a wedge off the end of that. Note that you can buy 20 degree plastic wedges, but this is the first one I have found that does 15 degrees (nominal.) Note that Amazon also has the Blue AngleGuide set of wedges, but they are very small
I enjoy these stones so much that the feedback is not a deterrent at all for me, I don’t even think about it. The results are always nothing but top notch, they deliver exactly what I want, some of the sharpest knives I have ever produced were sharpened on Shapton Glass stones. They may be thinner but they last a very long time, they are easy to maintain as well,
We're not completely sure but we think we now have the largest selection of sharpening stones on the face of the earth. If you're interested in something and don't see it here please contact us and we'll try to get it. Most of the stones you see here are Japanese water stones, both synthetic and naturals. There is also a wide selection of stone holders, flatteners, and other items that will help you get a razor sharp edge on all your sharp tools and knives.
Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
The Whetstone 2-Sided Sharpening Stone is made from professional grade corundum and will sharpen everything from a razor blade to a cleaver and even a machete, should you happen to have a machete lying about that needs sharpening. This is the simplest type of sharpener it’s true but the company have obviously put a great deal of thought into the product.

The Japanese sharpening stone whetstone combo is about 9.1 in. in length. It's  multi-sided and actually looks like a block of wood. When you use the dark side or the medium grit side (#1000), soak it for about 2-3 minutes.  When finished, the ridge on the base which surrounds the stone will fit snugged into it. Even if the base wasn't there the stones friction will stay. Some of the good features of the base is actually the rubber stoppers to hold it on a dry surface. When you learn how to sharpen a pocket knife, doing it on one of these will help.
Method 2: Send it out to a professional. This is a good option, provided you have a good knife sharpener living nearby, and are willing to pay to have the services performed. If you plan to sharpen your blades a dozen or so times a year, as I do, this can get quite expensive. All but the best professionals also use a grinding stone that, again, will take away much more material than is necessary from your blade, reducing its lifespan. Want to forge a stronger relationship with your blade? Then you'll want to...

Selecting the right sharpening angle is the next step in sharpening. For more detailed instructions on selecting the right angle, try reading this article. Regardless of the method of sharpening, a appropriate angle should be selected. This angle doesn't need to be exact but following some general guidelines is a good idea. Most knife manufacturers recommend a roughly 20 degree angle. Depending on the use of your knife, you can move up or down from that angle. A fillet or slicing knife is never used on anything hard so an angle a few degrees less will produce a sharper edge. On the other hand, a survival knife with various uses can benefit from a more durable edge a few degrees larger.