Put the pointed, narrow end of the sharpener up against the open end of the gut hook. The narrow, pointed end of the sharpener should face in toward the thickness of the blade, away from the edge of the gut hook. Match the angle of the sharpener to the original edge angle. This will maintain the correct sharpening angle and prevent you from getting cut by the blade tip. Hold the same angle when sharpening each side of the gut hook.
A: People often make the mistake of assuming that just because a mechanical knife sharpener will sharpen the edge of a knife that means it will sharpen any type of cutting edge, including scissors. This is a mistake and can wind up being a costly mistake when you have to replace both your scissors and the knife sharpener. There are sharpening devices specifically designed to handle scissors. Or you can bring your scissors to a sharpening pro who will usually have the right equipment on hand to also sharpen scissors. Another thing to keep in mind about trying to use a sharpener to sharpen scissors is that by using the device in this fashion you are likely voiding the warranty. As such if you damage the device trying to sharpen scissors you’ll need to pay to have it repaired or replaced as the warranty won’t cover it. Also, certain types of high end scissors also come with a warranty. And, just as with the sharpener itself, if you try to sharpen them using a mechanical sharpener you can say goodbye to the warranty protection. The bottom line is to always use the appropriate tool for the job at hand. That way you’re assured of the best possible result and any warranty remains in effect.
This is a good size stone and has the two different grits needed for knife sharpening. No instructions were included, but there are many websites with written and video instructions, so this is not an issue for most people. A fair amount of dust is generated during the sharpening process, so protect the work surface and wash the knife after sharpening is completed.
There will be a drawer that extends into the mechanism under the abrasives. Any detritus from the sharpening process drops into this drawer. Exactly where the drawer is located will differ from sharpener to sharpener but it shouldn’t be hard to find. Remove the drawer flick any material into the wastebasket and then wipe out the drawer with a damp cloth or tissue. You may want to use work gloves and goggles to protect your hands and eyes from any loose metal shavings. Once the drawer is clean and dry replace it. The exact means by which the sharpening mechanism itself is cleaned will vary from manufacturer to manufacturer. Consult your owners guide for specific details. Make sure you don’t introduce any grease or other lubricants into the sharpener unless specifically directed to do so by the owner’s manual. Also, the outside of the sharpener should come perfectly clean with just a damp cloth. Avoid using commercial cleaners or abrasives of any kind.
The composition of the stone affects the sharpness of the blade (a finer grain, usually, though not always, produces sharper blades), as does the composition of the blade (some metals take and keep an edge better than others). For example, Western kitchen knives are usually made of softer steel and take an edge angle of 20–22°, while East Asian kitchen knives are traditionally of harder steel and take an edge angle of 15–18°. The Western-style kitchen knives are generally in the range of 52–58 on the Rockwell scale, which denotes the relative hardness of a material.
Your immediate goal is to raise a burr on the side of knife opposite to the side you are sharpening and depending on the steel, the grit of stone and how you are doing, it will be either a very quick process or it will seem like it takes an eternity. Patience here will reward you, believe me. The sharpening process is incomplete with no burr creation on your first stone. (Yes, it is possible to stop at that magic moment without the burr forming but we are not there yet, we don’t even need to go there, ever, I am just mentioning it so those gifted sharpeners will be happy) . Think of the burr as the debris that is making the knife dull being forced down the blade towards the edge and over to the other side of the by your sharpening prowess. You form the burr, that knife will get sharp, no burr, you just need to look at your work. A Loupe is handy here, an inexpensive magnifying device with a light that allows you to see the edge very well, if you are not forming a burr, you are not reaching the edge. (Having a loupe also makes you look cool and scientific, like a Sharpologist).
For woodworking tools like chisels and plane blades, you will need stones that are at least as wide as the blades themselves. Length is helpful but not always critically important. The one exception is when you're using a guide for sharpening tools. The guide often rides on the stone and longer stones permit you to use a much larger portion of the stone as both the guide and the edge need to simultaneously touch the stones.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.