Push the point you want to sharpen with your fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone, then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures) Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade.
Method 1: Use an Electric Sharpener. Quality electric sharpeners are an option, but I strongly discourage their use. First off, they remove a tremendous amount of material from your edge. Sharpen your knife a dozen times, and you've lost a good half-centimeter of width, throwing it off balance, and rendering any blade with a bolster (i.e. most high-end forged blades) useless. Secondly, even the best models provide only an adequate edge. If you don't mind replacing your knives every few years and are happy with the edge they give you, they'll do the trick. But a much better choice is to...
At age 10, Terada learned the basics of sushi from his father and then went on to attend RKC Chef's School in Kochi, Japan from 1987-1989. He soon earned a nickname for his fast knife, attention to detail, divine presentation and ability to create new dishes and accents based on traditional Japanese cuisine. After graduating RKC Chef School, he was called to serve under Master Chef Kondo at Yuzuan restaurant in Kochi, Japan from 1989-1992. Mr. Kondo is the master of Kansai style cooking, considered to be the high-end of Japanese cuisine. Terada earned the title Master Sushi Chef by becoming the standing head sushi chef & can serve Fugu (Japan Licensed) to the public.
Selecting the proper coarseness for your sharpening stone is an important first step in sharpening your knife. Not every knife needs to start at the coarsest stone you have, on the other hand a very dull knife can not be sharpened on only your finest stone. Starting with the proper coarseness will ensure that you achieve the edge you need quickly. If your knife is very dull or has a nicked blade, start with your coarsest stone. The coarse stone removes material quickly so a poor edge can be refined quickly. However, the coarse stone must be followed up with your finer stone to refine the edge. If your knife is only slightly dull and just needs a quick touch up, starting at a medium or fine stone can save you time. Starting on a fine stone requires fewer steps but must only be used on an edge requiring little work.
In recent years, some whetstone manufacturers have started producing ceramic whetstones made from hard, ceramic, powders that are mixed with Aluminum Oxide and then sintered to form a solid. But, rather than using oil or water to lubricate the whetstone, ceramic whetstones are meant to be used without lubrication and thus, they provide a significant advantage for chefs who need to keep their knives sharp but, who do not have either the room or time for using a bench water stone. Thus, they are commonly available as either bench stones, pocket stones, round rods, or triangular rods.
Technically, the name whetstone can be applied to any form of sharpening stone, regardless of what cutting fluid is typically used with it. However because whet sounds like wet, many hear the word and assume that it refers to a stone that is used wet with water. Actually, water stones, oil stones diamond stones and ceramic stones are all forms of whetstones. So, while all water stones are whetstones, not all whetstones are water stones.
I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
A: Like cars, knife sharpeners run the gamut from basic to luxury and like cars the price can vary from extremely affordable to more than some people might want to spend. You can get a high quality sharpener that will put your knives through a 2 or 3-stage process which will result in an incredibly sharp edge for less than $20. Or you can buy a mechanical sharpener that will produce a virtually flawless edge for $200+.
The company is to be commended for including links to instructional videos in the package. Those videos lay out clearly how to get the most from your Whetstone sharpener stone. Once you get up to speed you’ll likely enjoy the process and at the same time achieve professional quality results time and again. Sure, it’s not fancy and doesn’t have a sleek, chrome plated design but it works.
Although there are many ways to sharpen your kitchen knives, we believe that using a sharpening stone is the absolute best way to go about it. Not only will you get the best results, you won’t assume as much risk of damaging the blade as you would using a manual or electric knife sharpener. The problem for most home cooks, however, is finding the best sharpening stone and learning how to use it. I’m not going to pretend it’s as easy as purchasing a stone and digging right in.
Method 3: Use a Sharpening Stone. This is the best method by far. Not only will it give you the best edge, it also removes the least amount of material. With a fine enough grit, your knife should be able to take hairs off your arm when you've finished. Additionally—and I'm not kidding about the importance of this one—the act of sharpening your knife will help you create a much stronger bond with your blade, and a knife that is treated respectfully will behave much better for its owner. The only problem? It takes a little know-how.
You’ll know you’re reached a stopping point when you can feel the slight catch of the bevel on the edge of the blade, by carefully running your finger in the direction of the blade, or by cutting through a sheet of paper. When the knife cuts cleanly through the paper, it’s time to hone the blade. Read our guide for more information about honing vs sharpening.
At this point, I can flip the stone over and use the fine course side. Most Whetstones come with a nice wooden base that do a good job to hold the stone in place while sharpening. Before starting, you might need to add a bit more water to the surface. Now with the fine course stone, finish the sharpening process like before at the same blade angle and nice consistent passes along the stone. About 10 to 12 passes is good before switching to the other side of the blade. At this point, the blade should be extremely sharp. I’ll just give a quick paper test here. I can now slice paper quite easily with my knife.
Whetstone has two different sides of grain for sharpening and polishing knife edges. These softer Japanese stones have several advantages over harder stones. Because they are softer, they do not become glazed or loaded with detritus. Plus, they are lubricated effectively with water rather than oil, but can be used with either. Submerge the stone in water for about 5 - 10 minutes. Continue to apply water while sharpening with the Whetstone Cutlery Two sided Whetstone Sharpening Stone. The stone releases small particles during the sharpening process; this powder in combination with water allows the sharpening. After a while you will notice a small burr at the edge. Now repeat the same process on the other side of the blade. Finally, turn the stone over and repeat the procedure, this time using the finer grit of the stone. In order to remove the remaining burr, pull the blade at an angle over the stone. Rinse the stone and clean off the grinding residue. Clean your knife with hot water.
This was the first Whetstone that I've ever purchased. After reviewing several 'how-to' videos, I jumped right in to use it. I found the process nearly meditative and the BearMoo stone extremely effective! The first knife I sharpened was very dull with small, jagged edges. The 1000 grit side effectively removed the jagged indentations and created a nice cutting edge. The 4000 grit side made the knife razor sharp. The process took nearly 40-minutes.
Whichever method you choose, be it a waterstone (also known as a whetstone), or a pull-through (either V-shaped or ceramic wheels) it's important to regularly hone your knife with a honing steel, which we'll also cover below. You'll be pleased to hear that you won't have to reach for the stones too regularly – once every two or three months should suffice.
A: We’re all told that a sharp knife is safer than a dull knife yet most everyone knows that merely touching a sharp knife can often result in a painful cut while we can wrap our hand around a dull blade with little worry. So why would anyone in their right mind claim that a sharp one is safer than a dull one? To a certain extent it’s a matter of semantics for sure, because there is no denying you have to be extremely careful around really sharp knives. But at the same time there is a very good reason to consider a dull knife to be more of a safety hazard than a sharp knife.
Clamp-style sharpening tools use a clamp with several holes with predefined angles. The stone is mounted on a rod and is pulled through these holes, so that the angle remains consistent. Another system is the crock stick setup, where two sticks are put into a plastic or wooden base to form a V shape. When the knife is pulled up the V, the angle is held so long as the blade is held perpendicular to the base. Several cutlery manufacturers now offer electric knife sharpeners with multiple stages with at least one grinding stage. These electric sharpeners are typically used in the kitchen but have the ability to sharpen blades such as pocket or tactical knives. The main benefit of using an electric sharpener is speed with many models that can complete the sharpening process in one to two minutes. The disadvantage is that the sharpening angle is fixed so some specialized knives, like a Japanese style Santoku, may need additional attention to sharpen to the ideal angle.
This is my first time ordering from hayneedle, but you came thru with flying colors. I was so happy to see the delivery come so quick as stated. It was just as i hoped it would be, i now have my whetstone sharpening stone, to really get my kitchen knives as sharp as i can get them. This to me is the best way to sharpen a knife, it takes patience but the reward is worth it. Thanks Hayneedle you rock!!! Ray D.
The type of stone refers to the material it is made with. You can find many different types, including diamond, ceramic, natural stone, and synthetic. I would only suggest diamond if you’re planning to be sharpening only ceramic knives. Many of the stones you’ll find on Amazon or other retails are made of Corundum, which is a crystalline form of aluminium oxide. It’s a fine choice for a beginner sharpening stone.
Choose the style of stone. You'll need to choose a natural or synthetic stone that can be used wet (soaked in water), with oil, or dry. There are also diamond stones that are actually very small diamonds attached to a metal surface. Stones that are soaked in water are softer stones which means you can quickly sharpen your knives. Unfortunately, these stones will wear down faster than the others. Oil stones are the least expensive and they're made of a harder material.