I have this one and the axe/machete version as well. These are great sharpeners that make very short work of getting blades sharp. They take off quite a lot of material and are quite different than most other stone sharpeners I have used in the past, so I try to be conservative with my pressure as you see the chips fall when you pull the knife through. But, they absolutely work, and work very well. If you have a high use knife, this is a great way to keep it sharp and in service all the time. I use my large bushcraft knife a lot more now that I have this since I can sharpen it much faster and easier. I would not use this sharpener on precision instruments just because I prefer more control and try to preserve material on those types on knives. But, bottom line, I get more work done and much faster now that I have this.
The goal in sharpening a serration is to maintain the ramp of the serration right to the edge. You do not want to create an edge bevel. Therefore we once again recommend the trusty felt pen trick. Paint the serration to be sharpened and follow your process. Evaluate if you are removing all the black. It should not take more than 5-8 strokes to resharpen if your angle was correct. Rotate or spin the sharpener as you go for the most even, consistent sharpening.
Now move the blade – with a little pressure – in regular strokes up and down across the sharpening stone. Always maintain the angle between the blade and the stone. You will notice a burr becomes visible after five or so strokes. Mentally divide the blade into three parts if the knife has a large blade. Always start with the tip and work back towards the bolster.

Looking for the best manual knife sharpener that’s easy to use and effective? Then consider getting the Brod & Taylor Professional which is a home foolproof knife sharpener that has a unique design to effectively sharpen smooth and serrated knives. Consumers find it very easy to use, sharpens all types of knives, sturdy that’s built to last, and quite attractive to sit on the counter.


This three stone package is a good place to look if a larger surface area in oilstones is what you’re after. The 11 1/2" long by 2 1/2" wide Coarse Crystolon, Medium India and Soft Arkansas stones provide more work surface than the smaller oil stones giving flexibility to sharpen knives and many other tools as well. The plastic housing retains the oil, keeping the stones bathed and ready to go.
So you are going to start at the heel and you are going to time it so that it goes all the way across. You go from one side to the other. You also want to make sure that your stone, I am not going to use as much pressure as I normally would because I cannot mount it on this showcase, you want to alternate from side to side to keep your bevel centered. Some people will take and do three times on one side and then three times on the other, the problem is that your backhand is never as good as your forehand and you end up cheating and you are going to end up with a blade that is offset. That is going to take it and thin down, you are going to get a thin bevel right on the edge. Once you get that V established, you can go from the coarser side to the finer side.
This coarse grit whetstone is great for prepping old and dull knives that need to be sharpened with a fine grit stone. One of my good knives edge looked like someone had tried to chop barbed wire. After ten minutes on each side of the stone, the edge was smooth and free of imperfections. After it hit the knife with the fine grit stone, I was cutting onions and apples like hot butter! I would soak this stone for 12-24 hours before using. It sucks water like a sponge. The surface needs to be damp when you sharpen.
Our test of the Brød & Taylor turned a dull blade into one that effortlessly and cleanly sliced both tomatoes and paper. Due to the reputation of V-notch carbide sharpeners, however, I was concerned about the durability of the edge, so I did an additional test: I used the Brød & Taylor to sharpen my old pocketknife, which uses 440C steel, one of the earliest knife-worthy stainless alloys and one that more refined alloys have since surpassed. I then made 50 slices through a cardboard box, rehoned and repolished the knife (but did not resharpen it), and made 50 more slices. After all that, I was still able to slice a tomato and peel an apple without problem. That’s impressive: Cardboard is so tough on blade edges that knifesmiths use it as a kind of stress test.
The stone – With a sharpening stone, the process is essentially the same as with the stick sharpener. The only difference is that you don’t hold the stone, you place it into its own holder (If it comes with one. If it doesn’t you’ll need to improvise) on a flat surface. Push the knife down the stone several times while holding it at a shallow angle and then flip it and pull it toward you several times to get the other side of the blade.

An extremely well written and informative article on sharpening. Overtime we all get to love certain stones for our sharpening needs. I am a huge coticule fan, and although i have used all the others, i always come back to this natural stone above all others. Still trying to figure if i chose it or it chose me! NEver the less there are so many options out there it is not hard with a little time and effort to find the right combination for your needs.
"How do I use this daunting metal rod?" I hear you ask. Well, it's not too hard, really. The best way for a beginner is to balance the steel on a surface with the tip secured by a damp tea towel. You want to get that angle right, whether it's around 15 degrees for a Japanese knife or 20 degrees on a German or French blade. Then swipe slowly down, away from you, making sure the whole blade is honed – around five swipes on each side should do. 
The Work Sharp WSKTS-KO performs double duty as a knife sharpener and a tool sharpener. Its ability to perform multiple tasks is part of why this sharpener looks so intimidating. Instead of using spinning discs like most electric sharpeners, this Work Sharp uses belts. In fact, it works a lot like a typical electric sander. A motor pulls the belts along so that they gently shave away at whatever you place them against.
A: Most chefs have their own personal favorite and that’s what it comes down to for just about everybody; personal choice. If you’re the kind who likes to get personally involved in the process you might want to opt for a stone or stick knife sharpener.  These will allow you a certain amount of satisfaction knowing it was your expertise that produced the razor sharp edge. Others, however, are quite content to let the machine do the work and that’s fine too.
The double sided 400 and 1000-grit Water Stone Sharpening Block by Whetstone enables you to safely and easily sharpen and polish your kitchen cutlery, hunting or pocket knives, blades and razors. You can even use it for your gardening tools! This stone only requires water, no oil needed! Made with durable green silicon carbide, this honing tool will last for years to come.
One of the main advantages of choosing this stone sharpener over others, is the ease of use, efficiency and consistency. It might take a while before you can properly sharpen with a wet stone. However, the Chosera 1,000, makes the whole process easy and fast. There are no complicated processes. All you have to do is push and pull your blade across the surface and you are good to go. You obtain a razor-sharp edge. In short, everyone can do it.
It’s up to you if you want to use a sharpening steel or a handheld knife sharpener for honing your knives. The handheld is really easy to use. For fast, effective sharpening, simply place the blade in the slot and gently pull it through a few times. If you want to use a sharpening steel, just make sure it has a higher hardness factor than the knife to be sharpened. One more important thing: don’t ever hone serrated knives. They must be sharpened by a professional or replaced. Period.

Method 2: Send it out to a professional. This is a good option, provided you have a good knife sharpener living nearby, and are willing to pay to have the services performed. If you plan to sharpen your blades a dozen or so times a year, as I do, this can get quite expensive. All but the best professionals also use a grinding stone that, again, will take away much more material than is necessary from your blade, reducing its lifespan. Want to forge a stronger relationship with your blade? Then you'll want to...


Now it's time to polish. This is when you'll swap over from the coarse grit to the finer grit (make sure this side is wet, too). I found the knife still had a bit of grime on it, so I gave it a wipe clean beforehand. The motion is exactly the same as with sharpening, but you can apply slightly less pressure, and limit to roughly 30 strokes on each side. 
If you want the highest quality knife blade you need to learn how to use a whetsone, the most effective Japanese way of sharpening knives is to maintain their edge crisp and sharp. Today only, get this audio bestseller for a special price. Whetstone will not only teach you the basics of knife sharpening, but also an essential range of other essential skills. You will learn how to thin old knives to renew them and make them as good as new. You will also learn how to create a knife sharpening plan that will have you sharpening knives like a professional Here Is A Preview Of What You'll Learn... The Basics of Knife Sharpening Types of Sharpening Stones A Brief Word About Grits About Whetstone Sharpening Stone How Often Should You Sharpen Your Knives? Developing Your Knife Sharpening Skills Using the Correct Angle Applying the Right Pressure Level Thinning a Knife And much, much more! Download your copy today! Take action today and download this audiobook now at a special price!
Cutting angle – With a manual stick or sharpening stone you set the angle yourself so this does not factor into the equation when choosing that type of sharpener. When shopping for an electric sharpener however it does. You’ll want to decide if you want your knives to have the 15 degree “Asian” style angle so that you can make precise cuts or the Western standard 20 degrees or 22-degree sharpening angle. Most people will opt for the 20 or 22-degree angle simply because their cuisine doesn’t call for a lot of finesse from their knives and those knives are probably of a heavier Western variety anyway.
If you’re sharpening high quality knives, you probably don’t want to use a cheapo sharpening stone. But if you’re just getting started with sharpening your pocket knife, there’s no need to get too fancy right off the bat. You can find a sharpening stone at most hardware stores for about $10. This one is very similar to the one I use. Nothing fancy. Most basic sharpening stones come with two sides: a rough grit and a fine grit. The finer the grit, the finer or sharper you can get your blade. You usually start off sharpening on the rough grit and then finish sharpening it on the finer grit.
Scissors get dull, too, but many sharpeners can’t handle their unique shape. This easy-to-use manual sharpener can handle scissor easily, and will also sharpen all of your non-serrated knives with ease. It’s ergonomically designed for either right- or left-hand use and has a protective finger guard so you can safely sharpen all the knives in the block.
×