Certain knife sharpeners require you to spend up to 15 minutes of your life, just to get the edge or sharpness that you desire. If you are a busy individual, you may not have all that time in your life, and that is where the SunrisePro Knife Sharpener comes in. It makes the whole process of sharpening a knife easy and fast. It doesn’t matter how dull or damaged your blade is, this machine gets the job done within a few seconds.
Every few months, you'll notice that your chef's knife has a harder time yielding perfectly thin slices and precise dices. You might even find your knifework is slipping—literally. And aside from being annoying to cut with, a dull knife can be seriously dangerous. To keep your fingers (and your dinner) in good shape, you'll want to learn how sharpen a kitchen knife by using a whetstone or a sharpener, and maintain that edge by honing it with a steel rod.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
Ye olde tomato test - After you have sharpened using one of the above sharpeners grab a firm tomato and try to slice it. If the blade is properly sharpened it will slice through the skin with virtually no effort and without pushing the skin inward first. If the skin is able to fight back against the blade then your knives are not properly sharpened yet.
The Adjustable Angle Pull-Thru Knife Sharpener will sharpen all your knives (hunting, kitchen, and pocket) at the same angle as the original factory grind. Stop messing with the complex, cumbersome, and time-consuming Precision Sharpening Kits and get a simple, easy to use knife sharpener that offers more angles and sharpens both sides of the knife blade at the same time.
It has amazing features that make it the go-to product. These include triple action, professional results, and effectiveness. It works well on blunt knives that can be annoying making them very sharp in just minutes. The design of this knife sharpener makes it comfortable to use and able to complement any kitchen. This knife sharpener is very budget friendly due to the price that it comes in. It has three slots that perform different functions according to the blade that needs to be sharpened.

Based in Lancaster, PA, WebstaurantStore is the largest online restaurant supply store serving food service professionals and individual customers worldwide. With thousands of available products and over 5.5 million orders shipped, we have everything your business needs to function at its best. Over the years we have expanded our selection of wholesale supplies and commercial equipment to include healthcare, educational, and hotel supplies.
This Messermeister rod is available in a 10-inch option and a 12-inch option, allowing you to select whichever suits you best. A general rule I like to follow in selecting a sharpening rod is to select one which is about the same size as my longest blade. As someone who’s longest blade is only 8 inches, I would select the 10-inch option. Most people will find themselves leaning toward that option, since bigger isn’t necessarily better. The rod needs only to be sufficiently long to allow you to sweep your knife down it without running out of rod before you reach the end of your knife. Anything too large will be difficult to control. Therefore, unless you are trying to sharpen a sword, I would advise against the longer option.
Electric sharpeners use rotating ceramic or abrasive-impregnated metal wheels to grind a new edge into a blade. Low-end models, which start at about $25, feature a single set of coarse wheels that produce a rough, if potentially serviceable, edge—it depends on how even the edge is, and that’s a matter of overall design and engineering. Higher-end models can cost $200 or more (and professional models for slaughterhouses can approach $1,000), but they feature stronger motors and multiple grinding wheels—coarse, fine, and often polishing/honing—that when well-engineered can put an extremely keen, durable edge on knives of every style and quality. 

Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
Furthermore, Novaculite consists of several different layers of stone of different densities, grit sizes, and colors. Thus, the red Novaculite layer (aka Washita Stone) is the both the softest and most coarse while, the next most coarse/hard grade is the grey/white Soft Arkansas stone; both of which cut relatively fast for a hard whetstone material and thus, they are an excellent choice for refining a bevel. Then, the next grade of coarseness/hardness is the hard Arkansas stone which is used to polish the bevel rather than define it and, last there are the grades of Hard Black and Hard Translucent Arkansas stones which are used for extremely fine honing and polishing of a cutting edge. Plus, it’s also the primary material in “Charnley Forest” (English) and “Turkey” oilstones.
The final Chef’s Choice sharpener on our list is the 316 Diamond Sharpener. Like the 15XV the 316 is at its best when used to sharpen Asian-style knives and it does so with unflinching effectiveness and speed. This is a compact, 2-stage electric sharpener that produces the 15 degree edge so favored in Asian cutlery. Ideal for the preparation of sashimi or sushi.
Frequently, our recommendation for beginning sharpeners is to start with diamond stones as their strengths make them ideal to build a sharpening toolkit around. Diamond stones are low maintenance and durable, lasting many years with only occasional cleaning. They are among the fastest stones to use making them time efficient. Diamond grit will handle even very hard steels, and diamond stones can be used for flattening waterstones. All these things make diamond stones a practical foundation for your sharpening toolkit.
For beginners, we’d recommend starting with a medium grit stone (1000) to remove chips and set a new sharp edge. If you’re up for a little more, a finer stone (6000 or 8000) will help polish your knife to a scary sharp mirror finish. We’d also recommend getting a flattening stone (a ‘stone fixer’) to ensure your sharpening stones perform consistently, though a lower grit stone can also serve a similar function. Lastly, while sharpening stone holders are helpful (and we use them), you can easily just use a damp towel to place your sharpening stones on during use for stability.

The following are my personal favourites and they are all synthetic stones, I do have experience with natural what stones but lets keep it simple, lets stick to synthetic water stones. Believe me, some of the world sharpest knives are sharpened solely on synthetic stones. Here are my personal favourites, I use these water stones every day and the order is not necessarily in priority, they are all good.

4. Start sharpening the first side of the blade. With your blade set at the prefect angle, you’re ready to start sharpening. Imagine you’re carving off a slim piece of the stone’s surface. Personally, I bring the blade into the stone. Other people stroke the blade away from the stone. Both ways work, so just use whatever technique you prefer. If the knife blade is curved or if it’s longer than the stone, you’ll need to sweep the blade sideways as you work, so the entire edge is sharpened evenly. Apply moderate pressure as you sharpen. No need to bear down hard on the blade. After you make one stroke, start back at the beginning and repeat. Do this about 6-12 times.


I liked the idea of three sharpener adjusting to different angles on the blades. However the reality is that when you drag your knife thru the sharpener the little carbide blades pop out of the sharpener. Once this happens they will NO longer stay in place. This happened to 2 different units. The first one I sent back. The second one i threw away. I recommend you AVOID this sharpener, its junk.
Now move the blade – with a little pressure – in regular strokes up and down across the sharpening stone. Always maintain the angle between the blade and the stone. You will notice a burr becomes visible after five or so strokes. Mentally divide the blade into three parts if the knife has a large blade. Always start with the tip and work back towards the bolster.
Your stroke can be straight or circular, from "hilt to tip" OR "tip to hilt," whichever is more comfortable. If you're using a small portable sharpener, stroke the blade in nearly a straight direction. Remember to always cut into the stone and never pull or drag your edge backwards. The blade edge should face in the same direction as your stroke. So, you're essentially moving the metal away from the edge. We recommend the circular stroke as it helps you maintain your angle instead of having to find it every time you lift the knife from the stone.
With its premium series Select II, the whetstone manufacturer Sigma Power Corporation from Tokyo addresses users of high-alloy steels such as HSS. These stones, too, are obviously intended to engender a grinding experience similar to that of natural stones. The special production process is expensive, but the Sigma Select II probably has no equal when it comes to demolishing steel.
Hold your knife at approximately 20° in relation to the honing rod. Your angle doesn't need to be exact, just approximate. Whatever angle you decide to choose, or unwittingly end up choosing, make sure to maintain the same angle throughout the honing process. Changing the angle used during the honing process won't smooth out the metal in the blade as much as using a consistent angle will.[4]
To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.

Oil Stones differ from water stones in that they require the use of honing oil to float the swarf (metal particles). Also, these stones are commonly made from one of three different materials consisting of Novaculite, Aluminum Oxide (Corundum), or Silicon Carbide (Carborundum) and they all use oil to lubricate the stone and suspend the swarf in order to prevent the stone from becoming clogged. Also, while Novaculite and Coticule are the most traditional types of oil stones, there are also synthetic oil stones made by the Norton abrasives company called “India Oil Stones”.

The angle on a Buck Knife is set based upon how we feel the knife will be used. Heavy use needs a strong and blunt "V" while skinning or filleting would need a deeper but more vulnerable "V". We tend to grind to 13-16 degrees per side (see illustrations). If you match the existing edge angle and hold the knife against the stone to cut evenly across the edge grind, you will produce an edge with a similar angle.
The kind of tech we love: compact, reliable, durable, attractive and cheap. Purists may feel that other sharpeners will produce a more perfect result but for 99% of the human race this sharpener will be everything the doctor ordered. Your blades stay sharp for a good long time thanks to the 2-stage sharpening process and if you’re a left handed chef you’ll love the fact that it works just as effectively for you as for anyone else.
Electric sharpeners use rotating ceramic or abrasive-impregnated metal wheels to grind a new edge into a blade. Low-end models, which start at about $25, feature a single set of coarse wheels that produce a rough, if potentially serviceable, edge—it depends on how even the edge is, and that’s a matter of overall design and engineering. Higher-end models can cost $200 or more (and professional models for slaughterhouses can approach $1,000), but they feature stronger motors and multiple grinding wheels—coarse, fine, and often polishing/honing—that when well-engineered can put an extremely keen, durable edge on knives of every style and quality.

If no metal is being removed from the edge of the blade, it’s considered honing. Whereas if metal is being removed from the blade edge this is considered sharpening. Certainly, even honing will result in some microscopic amounts of metal being removed from the blade edge but not enough to be visible to the human eye, so the above definition is basically a solid one.
One of the only things we don’t like about the Idahone is the lack of a prominent finger guard where the rod meets the handle. As a result, we highly recommend using the safer “supported” technique for honing a knife, as demonstrated in our guide to chef’s knives. In this method, the rod is held against the counter or cutting board, and blade always moves away from your body and grip-hand, greatly reducing the chance of a nasty accident.
Every few months, you'll notice that your chef's knife has a harder time yielding perfectly thin slices and precise dices. You might even find your knifework is slipping—literally. And aside from being annoying to cut with, a dull knife can be seriously dangerous. To keep your fingers (and your dinner) in good shape, you'll want to learn how sharpen a kitchen knife by using a whetstone or a sharpener, and maintain that edge by honing it with a steel rod.
I would say they are worth the money. Go for it. I took a blunted Pampered Chef kitchen knife from completely dull to razor sharp in about an hour (of bumbling and repairing mistakes LOL) heavy grinding. If you have a severely damaged blade, grab one of those cheesey two sided stones from Harbor Freight to do your heavy grinding. From there these stones will work very well.

Our second entry from Chef’s Choice is the 463 Pronto Santoku. This manual sharpener is super-simple to use and delivers fast, high quality results every time. While this is a “2-stage” system there’s nothing complicated about it. One slot is for sharpening and the other for honing. Both stages utilize diamond abrasive surfaces so your blades will retain its edge for a good long time.
This pocket-sized tool sharpens knives using carbide sharpening blades, then gives the knife a smooth finish using ceramic blades. A diamond rod is used for honing knives or for sharpening serrated knives. This is a great tool to keep in the toolkit, the tackle box, or to carry along when camping. Since it’s small, your hands will be close to your sharp knife blades as you work, so you might want to save it for occasional use rather than for sharpening all of your kitchen knives on a regular basis.
As you continue to repeat strokes on the first time, eventually a tiny burr will form on the other side of the blade. To check for it, place the blade on your thumb, and pull it backwards. If the burr has formed, it should catch slightly on your thumb (with really fine grit stones, say 2000 or above, you won't feel this). This may take up to 30 or 40 strokes, and is the indication that you should switch and start sharpening the other side.

Water stones can also be made out of natural or synthetic materials and they are fast becoming the most popular type of whetstone as they only require the use of water to lubricate the stone. They are not as messy to work with as an oil stone and deliver fast sharpening results but for even better results, soak the stone in water for 5 or 10 minutes.
Turning to the sharpeners themselves, we looked at aspects such as ergonomics, speed and simplicity of use, noise level and overall power (for the electric sharpeners), and build quality. We also weighed cost against performance to get a subjective measure of value. After two hours, we had clear picks for the winner and the upgrade choice, as well as an option for people who want high style along with high performance.

We used the honing rods on multiple knives, including our top pick for chef’s knives, the 8-inch Mac MTH-80—a hard Japanese blade—and a vintage 12-inch Wüsthof, a German knife with a softer blade. That covers the two main types of knives that people commonly own. To dull the knives between tests, we repeatedly sawed through 1-inch-thick hemp rope, a classic challenge used by knifemakers to demonstrate their blades’ durability. We focused on 12-inch rods, because a longer rod is easier to use—it offers more room to sweep the length of a standard 8- or 10-inch chef’s knife.


Looking for the best manual knife sharpener that’s easy to use and effective? Then consider getting the Brod & Taylor Professional which is a home foolproof knife sharpener that has a unique design to effectively sharpen smooth and serrated knives. Consumers find it very easy to use, sharpens all types of knives, sturdy that’s built to last, and quite attractive to sit on the counter.
A major benefit of sharpening your knives on a sharpening stone is that you can thin out your knife. When thinning out a knife, you grind away extra material on the sides of the blade, making the blade thinner. Thinning of a knife is useful for knives that are often sharpened, as the cutting edge gets fatter when the blade is sharpened more often. Thinning is of great importance for the preservation of good cutting properties.
If you're frustrated with the performance of electric knife sharpeners - or if you're just a bit of a control freak like me - the Smith's TRI-6 Arkansas TRI-HOME Sharpening System allows you to manually sharpen your knives. The system ships with three high-quality sharpening stones and the included bracket holds the stones in place so you can work efficiently and safely.
Best purchase I every made. while my knife doesnt cut a fine layer of tomato without touching it, it became as good as it was when I purchased. I recommend users to learn how to properly sharpen the knife. It took me about 30 minutes to sharpen a single knife to what it is today. The knife gets really sharp. Also, with use, the surface gets uneven. I recommend you draw a grid in pencil and then file using the grinder stone until the grids disappear. This ensures the surface remains flat during all use.
This tiny, retractable rod has actually been designed for light sharpening and honing all in one step. Based on its size, I believe that this rod is best used by those who are uncomfortable flinging long knives and rods around as they attempt to put a finer edge on their blades. Its compact nature also makes it perfect for those who need to bring it with them on the go.
×