Once sufficiently wet, it's time to position the stone on something solid, so it doesn't move about during sharpening. Many come with holders, but you can just place it on a slightly damp tea towel on the table. The stone should be roughly perpendicular to your body, though Warner told me it is sometimes easier to angle it ever so slightly to the right (if you're right handed). 
A: Like cars, knife sharpeners run the gamut from basic to luxury and like cars the price can vary from extremely affordable to more than some people might want to spend. You can get a high quality sharpener that will put your knives through a 2 or 3-stage process which will result in an incredibly sharp edge for less than $20. Or you can buy a mechanical sharpener that will produce a virtually flawless edge for $200+.
Whetstone has two different sides of grain for sharpening and polishing knife edges. These softer Japanese stones have several advantages over harder stones. Because they are softer, they do not become glazed or loaded with detritus. Plus, they are lubricated effectively with water rather than oil, but can be used with either. Submerge the stone in water for about 5 - 10 minutes. Continue to apply water while sharpening with the Whetstone Cutlery Two sided Whetstone Sharpening Stone. The stone releases small particles during the sharpening process; this powder in combination with water allows the sharpening. After a while you will notice a small burr at the edge. Now repeat the same process on the other side of the blade. Finally, turn the stone over and repeat the procedure, this time using the finer grit of the stone. In order to remove the remaining burr, pull the blade at an angle over the stone. Rinse the stone and clean off the grinding residue. Clean your knife with hot water.

3. Place the knife blade flat on the stone and raise it to a 10 to 15 degree angle. The key to knife sharpening is maintaining a constant angle. Different knives require different sharpening angles. For a pocket knife, shoot for a 10 to 15 degree angle. This will give you an edge that’s sharp enough for most daily needs, but not sharp enough to perform heart surgery.  Keeping a constant angle by hand takes a lot of practice. If you’re having difficulty, you might consider investing in a sharpening guide. It takes all the guess work out of maintaining the needed angle. They cost about $10.


If your knife isn’t restored by steeling, you may need to hit the fine ceramic stone a few times. You should rarely need the coarse notch after your knife is properly sharpened. That is, unless you’ve wrecked the edge by cutting on a too-hard surface or trying to hog your way through a bone. If that’s the case, you’ll have to hit the coarse and then the fine.
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
It has amazing features that make it the go-to product. These include triple action, professional results, and effectiveness. It works well on blunt knives that can be annoying making them very sharp in just minutes. The design of this knife sharpener makes it comfortable to use and able to complement any kitchen. This knife sharpener is very budget friendly due to the price that it comes in. It has three slots that perform different functions according to the blade that needs to be sharpened.

It is designed to help sharpen straight bladed knives that are made of steel. It cannot be used on ceramic and serrated edges. The two sharpening modes guarantee the user gets the best service from it. It has been designed with the users’ safety in mind. This is due to the large grip handle and the non-slip feet. It has an attractive design that makes it a great addition to any kitchen.

The final Chef’s Choice sharpener on our list is the 316 Diamond Sharpener. Like the 15XV the 316 is at its best when used to sharpen Asian-style knives and it does so with unflinching effectiveness and speed. This is a compact, 2-stage electric sharpener that produces the 15 degree edge so favored in Asian cutlery. Ideal for the preparation of sashimi or sushi.
Silicone Carbide whetstones on the other hand, are the fastest cutting of the three types of oil stones and the stones made by Norton are called Crystolon Stones. Also they too are graded as either fine, medium, or coarse stones depending on their grit. But, although these stones will not produce an edge as fine as Arkansas Oil Stones or India Oil Stones, their fast cutting ability makes them ideal for sharpening tools as well as for cutting the initial edge bevel on extremely dull knives or repairing the edge on damaged blades. Last, because they sharpen so quickly, it a common practice to start with a coarse Crystolon Oil Stone and then progress to either a medium or fine India Oil Stone and then to finish with an Arkansas Oil Stone.
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.

The Chef’s Choice 476 2-Stage Sharpener transforms your weary kitchen, hunting and pocket knives into razor sharp cutting instruments with dependable ease. The sharpener is simple in concept, solid in its fabrication and reliable in the way it goes about its business. The design is also free of right-hand bias which is good news for the lefty chefs out there.
Sharpal 178N TRANSFORMAN 3-In-1 Diamond Round and Tapered Sharpal 178N TRANSFORMAN 3-In-1 Diamond Round and Tapered Rod Sharpener makes it easy to sharpen all kinds of knives including those with serrations gut hooks fishhooks and pointed tools. Industrial monocrystalline diamond is electroplated in nickel onto a steel base. Sharpen dry. No messy oil needed. Fine 600 grit (25 ...  More + Product Details Close
Works well. Just got it today, sharpened two pocket knives, one a 8Cr13MoV Chinese steel, the other s30v American steel The stone made short work of both steels (which were pretty sharp already). But notably was able to make the s30v hair shaving sharp easily, something I've had trouble with. Inexpensive and useful, I love this stone. It's not the Ninja sharp 8000+ grits that you can find, but for pocket knives and EDC, it's perfect and inexpensive. Get One!!!!!!!!!!!!
Now turn the knife so that the blade is no longer pointing towards your body. Continue to maintain the angle of 10 – 20 degrees and the gap of approx. 5 mm from the back of the blade to the sharpening stone. Slide the cutting edge up and down over the sharpening stone. Grind both sides of the blade alternately, around five to ten times on each side.
Honing is kind of like dusting the furniture while sharpening is more like reupholstering the furniture. Honing is purely a maintenance activity that should be regularly practiced to make sure the blade is clean and sharp as can be every time you use it. It’s easily done using a honing rod, a leather strop or a sharpening stone; as most stones have a side for sharpening and a side for honing. Honing is akin to trimming your hair to remove the split ends. It’s not a full on haircut. What it does is realign the tiny sharp protrusions along the edge of the blade that can be bent over with use, so that they stand more or less straight.
The SunrisePro Knife Sharpener is designed to make your cutting life easy. This USA-made and patented knife sharpener, features a striking red theme and an unusual design. It has an advanced grinding system, which allows you to sharpen different types of knives. This 100% original knife sharpener, also comes with a powerful suction cup. It is quick and easy to use. This SunrisePro Knife Sharpener review, tells you everything that you need to know about this product.

There really is no point in having amazing knives if you don’t keep them sharp. Bert from TOG Knives has spent years experimenting with different sharpening methods and bits of equipment to work out the absolute best way to sharpen TOG Knives. If you follow the advice below we guarantee you will become a sharpening Ninja. Watch this space as we’ll be adding more videos in the future…

×