The most important aspect of a sharpening stone is the grit. If you have knives that have taken a beating and are either nicked up or really dull, you’ll need a courser stone to get it back into shape. And in order to put an exceptionally sharp edge on an already sharp knife, you’ll need a finer grit stone. If your knives are already in pretty good shape and just need a touch up, buying just a finer grit stone might be enough, but don’t think you can get away without a courser stone for knives that need more TLC. It is possible to buy a combination, or two-sided sharpening stone.

Very handsome and functional. The leather that makes up the necklace is high quality and the knot they use is seldom seen. I was able to touch up my bark River gunny sidekick with it( m4 steel at 62-64 hrc!), And that is saying something. Haven't tested the fish hook groove, because I don't generally fish in the winter, but I'm looking forward to trying it out
I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
In terms of feedback, in the eyes, and in the hands of many sharpeners, the feedback on this particular brand of stones is not to their liking and often it is enough to stop them from using them. These are thinner than other stones as well so you may get the impression that you are not getting your moneys worth. They are very hard stones, there is no soft, creamy sensation as you sharpen, there is not much feedback at all in fact.
A: When it comes to the best knife sharpeners used in a domestic setting the abrasives used to sharpen the blade should last for quite a few years. When they do eventually wear out many of the best manufacturers will refurbish them for you, typically for a nominal fee. Again, however, unless you are using the sharpener on a daily basis (and there is virtually no reason the average person would do this), the sharpener should last for many years before ever needing service.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
×