Cost – While you can get a perfectly serviceable sharpening stick or stone sharpener for short money and some very high-quality tabletop manual 2 and 3-stage sharpeners for less than $50, high-quality mechanical systems will often run you $200 or even more. While that’s not so much money it’s likely to impact the quality of your life it is a lot to pay to keep a decent edge on your knives. While how much you ultimately pay for a sharpener is entirely up to you, you may want to consider your commitment to cooking and how often you are actually liable to use the device. If this is your first sharpener you might also want to consider learning how to sharpen a blade using a classic stick or stone sharpener first, before deciding if moving up to a mechanical sharpener is the right thing for you.
We tend to recommend natural Japanese water stones only to experienced users who are thoroughly familiar with the synthetic Japanese sharpening stones. Natural stones are not to everybody’s taste and there are inevitably many uncertainties with regard to their grit grade, which cannot be determined exactly, their hardness and their suitability for certain types of steel.
The Japanese sharpening stone whetstone combo is about 9.1 in. in length. It's multi-sided and actually looks like a block of wood. When you use the dark side or the medium grit side (#1000), soak it for about 2-3 minutes. When finished, the ridge on the base which surrounds the stone will fit snugged into it. Even if the base wasn't there the stones friction will stay. Some of the good features of the base is actually the rubber stoppers to hold it on a dry surface. When you learn how to sharpen a pocket knife, doing it on one of these will help.
If in doubt or just learning, a safe bet is a set of quality synthetic stones. They’re the easiest to use, require the least maintenance and are the most forgiving. If you’re just starting out we highly recommend the Naniwa Sharpening Stones. They’re excellent quality, reliable, durable and no soaking time is required. For advanced users we recommend the Naniwa Pro sharpening stones or Kaiden Ceramics.
Finally, when you learn how to sharpen a pocket knife becomes reality, you'll ultimately see the difference in your blade. Every sportsman and kitchen guru should learn how to sharpen a pocket-knife the proper way without "nicking it" or "shaving the edges" off too much you end up with a short and stout blade. Consequently, selecting the proper pocket-knife sharpener is important so learning the in's and out's of how to sharpen a pocket-knife before and after using it is all in the practice as well as in the sharpener itself.
Serrated blades have a grind on one side of the blade. Only sharpen the grind side of the blade. Hold the sharpener at the angle that matches the original edge angle. Hold the knife with the edge away from you and the serrated side of the edge facing up. Set the tapered diamond sharpener in a serration so that you fill the indentation. Draw the sharpener towards the edge.
Feedback is something that is very important to most sharpeners, i.e. how the stone feels when you are using it. Does it feel smooth, creamy and silky or does it feel hard and scratchy. While feedback, pleasant or unpleasant may be a purchase deterring factor it really doesn’t have any effect on level of sharpness that the stone can deliver. Unless of course the feedback is so distracting that it hinders the sharpeners focus and enjoyment and as a result, the sharpener doesn’t like what he/she is doing so that ultimately it does have the potential to negatively impact the results.
Mine came plain white then started to darken after a few weeks. About 4 weeks in it settled to a more natural stone/slate grey. The leather has darkened a bit too and remains soft and comfortable. The leather remains easy to adjust and my selected sizings stays in place firmly. Overall It feels, looks and works great. The knot and darker stone/leather compliment each other well.
Now you are going to use P2 pressure, moderate and in this case the stone is going to do the work, you are just guiding the knife along, stabilizing it as the amazing water stones does it’s job. Use the exact same technique, same angle but just moderate pressure, hardly pressing down at all, you are not trying to form a burr here, that is already done, now you refining the edge and bevel, removing some of the scratches left by your first stage of the process. Here is where the knife will get sharp and it will happen quickly. Now you are removing the burr, you are cleaning up the edge, some of that fatigued metal is going to want to hang on to the mother ship, your moderate pressure is going to start taking it away, as reluctant as it is to leave, it won’t have a choice. This should only take a couple minutes just mimicking the first step but with lighter pressure and this time visualizing the burr being scraped away, it will start to vanish.
Both Belgian Blue and Vielsalm Coticule are ancient stone layers found in the Belgian Ardenne Mountains with characteristics similar to both Novaculite and Siliciclastic sedimentary stone in that it is a metamorphic stone consisting of both gray and yellow volcanic ash mixed with tiny Spessartite Garnet crystals suspended in a clay matrix. However, due to its geology, both types of stone occur only in vertical seams sandwiched between two thick layers of bluish-purple slate and thus, they must be meticulously extracted mostly by hand. However, this type of extraction process is both very time-consuming and very labor-intensive and, quarrymen can only extract the stone for a few months each year due to inclement weather conditions. Consequently, both Belgium Blue and Coticule whetstones tend to be somewhat expensive.
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me.
I really liked this whetstone! I had a Smith's pocket sharpener that could get my knife sharp enough for working around in the yard (I have an Opinel no.8). However, in doing a little research I found that the sharpener was only around 600 grit on the finest setting. So this BearMoo 1000/4000 grit looked like the perfect step up, and it turned out to be the perfect stone for me. The pictures are an accurate representation of what you get. The removable rubber base was helpful when switching from one side to the next, and it kept the stone from sliding around. The instructions say that the stone can work with either water or oil, but that water is preferred. It said to leave the stone soaking in water for five minutes, and the stone worked like a champ. I especially liked how the instructions gave you an approximate time of how long the stone takes to sharpen a knife -- it just helped give me an idea that it would take about 15-20 minutes on the 1000 grit side, and then another 10-15 minutes on the 4000 grit. Just turn on a TV show!
Diamond sharpening stones are becoming really popular because of their ability to cut fast. We tend not to recommend diamond sharpening stones/plates because a lot of damage can be done very quickly. Also diamonds are pretty sharp and at arato level they leave deep scratches in the blade that need to be polished out quite aggressively. Diamond stones can be used with and without lubricant.
The DuoSharp Plus stones are nicely sized at 8” long by 2 5/8” wide and have two grits on each stone to maximize value. The Plus in the name refers to an area of continuous grit in the otherwise interrupted grit surface of the stone. This area is for sharpening edges with fine points that might be difficult on the interrupted surface. A coarse/fine DuoSharp Plus stone is a good single stone to start a sharpening toolkit.
first time buying a sharping stone. i bought this because i wanted to sharpen kitchen knives. you have to practice to get good at it, use a knife you don't care about because you might mess it up. there is some conflicting instructions online on how to use, water or no water. read as much as you can about using stones and practice, practice , practice. look up videos on youtube and internet. i had fun using it, BUY IF YOU WANT TO LEARN here is some stuff i found, they all sound like professionals http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 http://culinaryarts.about.com/od/knivescutlery/ht/whetstone.htm this is a video that says don't use water http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 this is a youtube video that i watched that uses water. *informative http://www.youtube.com/watch?v=KFIg9Cm-nJg
If you wish, further polish or even strop the edge to the desired sharpness. This makes the edge better suited for "push cutting" (cutting directly into materials, pushing straight down without sliding the blade across the object) but generally impairs slicing ability: without the "microscopic serrations" left by grinding with a stone, the blade tends to not bite into things like tomato skins.
Table mounted device – Typically the manual powered table mounted sharpener looks virtually identical to the electric powered sharpener with a slot for each stage. Where they differ is that each slot in the manual powered sharpener has only one groove and you pull the blade through this groove toward you to sharpen the blade. Once the blade is sufficiently sharp you place it in the honing groove to refine the edge and pull it toward you again several times. If there is a third, cleaning, stage you repeat the process for that stage as well.
Sharpening on the other hand is reupholstering the furniture or telling the hair stylist to give you a new look. Material is going to be removed from the edge of the blade. There’s no way around it. How much is removed will be a function of just how dull the knife has become or whether you’re sharpening to compensate for a chip in the edge or because the tip has broken off. If your knife is not damaged and you have it sharpened twice a year very little material will be removed each time, yet it may still be enough for you to notice just by looking carefully with the naked eye.
TO USE: Soak stone in water for no more than 5-10 minutes. Place stone on a damp cloth with the courser 400 grit side (dark green) facing up. Hold the knife so that it’s flat and perpendicular to the block, with the blade facing left. Holding the knife at a 20-degree angle, slowly sweep the edge of the blade from left to right down the length of the stone and continue until sharp. If stone starts to feel too dry, add more water. Be patient and take your time. Flip knife over and repeat on the other side (now moving from right to left). Be sure to sharpen both sides evenly. To polish the blade further, flip stone over to the fine 1000 grit side (light green) and repeat the process. When blade is honed to desired sharpness, wash and dry your knife. To clean your stone, simply rinse with water, wipe away any remaining metal residue with a rag, rinse again, then dry.
For instance, American Novaculite (aka Washita and Arkansas Stones) is a form of metamorphic Chert that produces some of the best known and best loved natural whetstones in existence. Then, there is a form of Belgian Coticule which has been known for providing extra-keen edges since Roman times and, there is a Japanese Siliciclastic sedimentary stone (aka Japanese Water Stones) which consist of a fine silicate particles suspended in a clay matrix. Plus, there are also various types of man-made whetstones available such as Silicon Carbide (aka Crystalon) stones and Aluminum Oxide (aka India Stones) as well as a synthetic Corundum (aka Ruby) rod and Aluminum Oxide impregnated ceramic rods as well as several different types of diamond hones.
You will also need at least one finer stone. Once the shape of an edge is established, successively finer grits are used to refine the edge improving the quality of the cut it delivers. A dull edge will not cut well and should be shaped with a coarse stone. An edge sharpened on a coarse stone will cut better than a dull one, but still won’t be ideal and should be improved with a finer stone. As you progress through finer stones, the cutting edge will continue to improve. How many and how fine these stones need to be varies depending on how fine an edge you require.
Here is what you need to get started and it does not begin with the tangibles. Success will come quickly if you understand and can visualize what it is you are attempting to do, what has to happen to make a knife sharp. My experience is with Japanese Water Stones but the same will hold true for other methods. I do not recommend pull through gadgets or electric grinders of any type by the way, I am opposed to those methods although I understand the desire to try everything out… remember, I thought I needed everything and I thought everything worked.
Pressure is something that is sometimes not mentioned but in my experience and in my opinion, it is extremely important to apply the correct amount of pressure, I use three different levels of sharpening pressure, with my sharpening pressure being measured on a scale from 1-5 with 1 being very light and 5 being maximum pressure. When you initiate the sharpening process, when you have all your ducks lined up and you are ready to start, use P4 (Pressure at level 4, almost maximum). in this case it is you and the stone working together, you are going to apply pressure with your finger tips (2 or 3 finger tips) placed as close to the primary edge as you can get, i.e. over the area you are working on, on the opposite side of the blade. As you push the knife away from you in a trailing motion, apply P4 pressure to the knife as it glides over the wet whetstone, (whet means sharpen) you will see the black residue start to form in the water on the surface, this is Swarf and this is good, don’t feel obliged to remove this with water, it is fine. Continue working from the heel to the tip of the knife moving your fingers along the edge and applying pressure as you move the knife away from you on the right side of the knife and as you pull it towards you on the left side, these are called edge trailing strokes.
In summary: Peter Nowlan is a professional knife sharpener based in Halifax (Canada) and he recommends the KnifePlanet Sharpening Stone Set, a beginners and intermediate kit that includes 4 sharpening grits: 400/1000, 3000/8000, a bamboo base and the KnifePlanet Flattening Stone. The Japanese Naniwa 3-stone combination is also a great (and more expensive) choice, ideal for professionals and more advanced sharpeners: the Naniwa stones are slightly bigger compared to KnifePlanet’s. In both cases, a coarse, medium and fine grit combination is very effective to sharpen and refine the edge:
These are unquestionably great starter stones. After all the sharpening done over the course of a couple days, they're still perfectly flat, showing little to no signs of wearing down. Mind you I did watch tons of how-to videos online before undergoing the endeavor, so I knew how to try to make the stone wear evenly. But, my 15 year old nephew who was working on the Ontario, as I told him he could have it, if he wanted to fix it up, didn't watch all those videos and I didn't see any uneven wear on his stone after working it about a half hour either.
if you have regular kitchen knives it will not work- first its to deep and the blade does not stick out, not dinner knives but cooking knives. of all the knives i put in it only 1 was wide enough to stick out. the device does not hold the blades. all the blades tested fell out of it, even a hunting knife, maybe its for 1 type of knife and they are selling it as the must have tool for all.. that said sell something useless for a few bucks that most cant use, they got a few bucks that most will blow off and not worry about a refund.. DONT WASTE YOUR MONEY.
The type and size of the blade being sharpened determines the size of the stone needed. In general , a 6" stone is considered a small sharpening stone, an 8" stone is a common larger size, and a stone larger than 8" (10"-12" are available) is considered generously sized. Stones smaller than 6" (3" and 4" stones are quite common), are considered pocket stones and can be used for toolboxes, tackle boxes and on-the-go sharpening, but are generally not recommended for regular sharpening jobs.
One more thing to consider before you proceed is if you would like to sharpen your knife freehand or use a guide such as the DMT Sharpening Guide. Your skill and experience in sharpening will help you decide on the method that's best for you. If you are experienced and comfortable with freehand sharpening, a knife guide may be unnecessary. On the other hand, a knife sharpening guide is an inexpensive and easy way to keep the angle consistent. If you have tried to sharpen before but never achieved the proper edge, we recommend using the sharpening guide. The guide can solve common mistakes in the sharpening process. If you choose to use a guide, please read our how-to for using the knife sharpening guide.
You might not need to spend hundreds of pounds to get the best knife sharpener, but you do need to know what you're doing. Warner gave me a crash course in the technique. As a newbie to this method, it took a while to get used to (especially since Warner handed me a knife that had never previously been sharpened) but after half an hour's practice and a little encouragement, I got the hang of it. Here's what I learned...
In terms of feedback, in the eyes, and in the hands of many sharpeners, the feedback on this particular brand of stones is not to their liking and often it is enough to stop them from using them. These are thinner than other stones as well so you may get the impression that you are not getting your moneys worth. They are very hard stones, there is no soft, creamy sensation as you sharpen, there is not much feedback at all in fact.
http://www.youtube.com/user/MakeSushi1 is all about how to make sushi, we pride ourselves on creating new exciting sushi roll recipes and then sharing them with the world. In our video tutorials we will teach you how to do all a basics of making sushi and create innovative sushi rolls, sashimi, nigiri sushi and possibly might create a new category of sushi , who knows. Subscribe to our YouTube channel to be notified of our weekly sushi videos: http://www.youtube.com/subscription_c...
The humble sharpener tends to elicit more divergent opinions than just about any other type of kitchen tech. Everyone, it turns out, has their own take on which type of sharpener works best and why and most serious chefs aren’t shy about voicing their opinion. As you can imagine then there are a number of things most chefs – both professional and amateur – look for in a sharpener in order to ensure they get the one that’s right for them. These considerations include:
Works well. Just got it today, sharpened two pocket knives, one a 8Cr13MoV Chinese steel, the other s30v American steel The stone made short work of both steels (which were pretty sharp already). But notably was able to make the s30v hair shaving sharp easily, something I've had trouble with. Inexpensive and useful, I love this stone. It's not the Ninja sharp 8000+ grits that you can find, but for pocket knives and EDC, it's perfect and inexpensive. Get One!!!!!!!!!!!!
I like the fact that there are two different grits (can be seen as two colors). the black rubber feet stick to the kitchen granite top like glue. The 1000 does a pretty good job of getting a knife roughly there and the 4000 puts on a fine polish for razor a sharp edge. I would go the extra step of stropping the knife after the grinding operation for an extra sharp edge.
This is a good size stone and has the two different grits needed for knife sharpening. No instructions were included, but there are many websites with written and video instructions, so this is not an issue for most people. A fair amount of dust is generated during the sharpening process, so protect the work surface and wash the knife after sharpening is completed.
At age 10, Terada learned the basics of sushi from his father and then went on to attend RKC Chef's School in Kochi, Japan from 1987-1989. He soon earned a nickname for his fast knife, attention to detail, divine presentation and ability to create new dishes and accents based on traditional Japanese cuisine. After graduating RKC Chef School, he was called to serve under Master Chef Kondo at Yuzuan restaurant in Kochi, Japan from 1989-1992. Mr. Kondo is the master of Kansai style cooking, considered to be the high-end of Japanese cuisine. Terada earned the title Master Sushi Chef by becoming the standing head sushi chef & can serve Fugu (Japan Licensed) to the public.